Bedienungsanleitung Henkelman MARLIN (Seite 40 von 43) (Englisch)

647373

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 40

REMARKS ON SPECIAL APPLICATIONS

MACHINE WITH GAS FLUSH SYSTEM (if applicable)

If the machine is equipped with the gassing system then the following remarks are important :

NEVER USE GAS MIXTURES WITH MORE THAN 20% OXYGEN AND OR OTHER EXPLOSIVE GASSES. THIS

COULD CAUSE FATAL EXPLOSIONS.

NEVER USE SEPARATE GAS BOTTLES WITH A MIXER WHEREBY ONE OF THE BOTTLES IS ONLY FILLED

WITH OXYGEN. MALFUNCTIONING OF THE MIXER OR IF THE OTHER BOTTLE WERE TO BE EMPTY COULD

CAUSE FATAL EXPLOSIONS.

All guarantees and/or liability expire in the case of accidents and/or damage caused by using oxygen or other explosive

gasses.

The maximum gas pressure that can be set in the packaging is 35% (-0.35 bar on the vacuum meter). This means that

there is 65% gas and 35% vacuum (under pressure) in the packaging. If a higher gas pressure results in insufficient seal

quality contact the supplier or Henkelman BV for more information about connecting external seal pressure.

Henkelman recommends checking the pressure and amount of gas in the gas bottles regularly. Ensure that the gas

bottle(s) is(are) correctly anchored. Always turn off the main cock on the gas bottle if the machine is not in operation or if

the gas flush function is not active.

PACKAGING LIQUID PRODUCTS

The machines can be also used for packaging liquid products like soups or sauces. In this process the vacuum process

must be carefully monitored (only possible with transparent lid or lid with inspection window). The [STOP VACUUM] key

must be pressed as soon as bubbles appear in the product; the saturation point (same as boiling point) has then been

reached.

Settings for programs for packaging liquid products can best be programmed using automatic programming (see page

19-20).

The saturation point of liquids is reached at a certain ratio line of low pressures and high temperatures (see the example

table for water below). The saturation point will be reached sooner in the vacuum process when packaging liquids with a

high temperature (the amount of vacuum will therefore be less).

Henkelman recommends therefore to first cool liquid products before packaging. By so doing an optimal vacuum can be

achieved for the product.

Saturation point of water – relation between the pressure and temperature of the water

Vacuum pressure

[mbar]

1000 800 600 400 200 100 50 20 10 5 2

Boiling Point

Temperature [°C]

100

-2

-13

A handy tip when packaging liquid products is to use a liquid insert plate so that the product remains at the bottom of the

packaging during the vacuuming process and there is less risk of liquid splashing out of the packaging. Contact the

supplier or Henkelman BV for more information about the liquid insert plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman MARLIN Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman MARLIN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info