Bedienungsanleitung Henkelman POLAR (Seite 12 von 43) (Englisch)

647375

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 12

STANDARD OPERATING STEPS FOR THE MACHINE

1. Turn the machine on with the ON/OFF switch. Heat up the pump with the condition program when machine has

stood idle for some time (instructions page 22).

2. Fill the vacuum bag with product. Select the correct format bag that easily fits around the product but is not too

large for the product. Ensure hygienic conditions during this operation. Packaging materials, product and hands

must be clean and if possible dry.

3. Lay the vacuum bag in the chamber or on the working plate. The open side must be

laid over the sealing bar or silicone holder. The bag may however not extrude from

the chamber. If the product is a lot lower than the height of the sealing bar or silicone

holder then insertplates which are supplied standard with the machine can be used.

This makes the operation easier and reduces the cycle time.

4. The vacuum bag must be laid without folds over the sealing bar (BOXER and

MARLIN) or silicone holder (FALCOM and POLAR).

5. For a gas flush system the opening of the vacuum bag must be pulled over the gas

nozzles (see illustration).

6. Multiple vacuum bags can be placed over the sealing bar/silicone holder if the sealing

bar/silicone holder is longer than the vacuum bag. Vacuum bags may not however be laid

on top of each other on the bar/holder. If there are multiple bars/holders then all bars/holders can of course be used

during the same cycle.

7. Use the [PROG] key to choose the desired program. See page 18 for instructions about programming.

8. Close the lid and the machine automatically runs through the full cycle of all activated functions. The lid opens

automatically when the last function “ventilation” has been completed.

9. If necessary the cycle can be partially or fully interrupted by pressing the [VACUUM STOP] key or the [STOP] key.

The [VACUUM STOP] key interrupts the active function (vacuum, gas flushing, sealing, or soft-air ventilation) and

automatically continues with the next function.

The [STOP] key interrupts the entire cycle and goes immediately to the ventilation function.

10. After cycle completion, the packed product (or products) can be removed from the machine.

11. If the machine is equipped with a cut-off sealing system then the remaining flap on the vacuum bag can be torn off.

SAFETY and PRODUCT PROTECTION

The packing process can be partially or fully interrupted at all times:

 Stop active function, press [VACUUM STOP] key

 Stop full machine cycle, press [STOP] key

OPTIMAL AND EFFICIENT PACKAGING RESULT

 Use the correct size and good quality vacuum bags

 Maximum 75% product filling in vacuum bag

 Place vacuum bag fold free over sealing bar/silicone holder (use correct number in insertplates in chamber)

 Pull vacuum bag far enough over gas nozzles (for gas flush) so that no gas is lost and the bag does not

move during gas flushing

BOXER / MARLIN series

FALCON / POLAR series

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman POLAR Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman POLAR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info