Bedienungsanleitung Henkelman POLAR (Seite 26 von 43) (Englisch)

647375

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 26

Replace sealing wire and teflon tape

1. Remove the sealing bar(s) from the holders (in the chamber or lid) by releasing the click

system or by unscrewing the screws.

2. Remove the teflon tape from the sealing bar.

3. The old sealing wires and cut-off wires (if applicable) can be removed by unscrewing the

clamp (see illustration) and pulling the wires from the grooves.

4. Remove the teflon tape that is attached to the top of the sealing bar and stick a new piece of

teflon tape to the bar of the same length after having degreased and cleaned the bar with a

dust free cloth.

5. Cut a new peace of sealing wire or cut-off wire to the size of the sealing beam plus about 15

cm (± 6 inches). If 2 sealing wires or an extra cut-off wire is on the sealing beam then a

second sealing wire or cut-off wire must of course be cut.

6. Place the end of the wire or wires through the groove(s) on the side of the sealing beam and

screw the wires to the bottom.

7. Place the sealing bar top down in a vice and pull the sealing wire or wires through the other

side of the groove(s) on the sealing beam.

8. Pull the wires tight with a pair of pliers and screw them down at the same time. Ensure that

the wire (wires) is (are) pulled taught and straight with the help of a pair of pliers before the

wires are screwed down.

9. It is handy to use a pair of adjustable pliers as a lever for optimal wire tension. Place one end

of the sealing beam in the vice and stretch the wire (wires) by pressing down the bar.

10. Cut off the extruding wire end(s) on both ends after having screwed it tight.

11. Cut a piece of teflon tape as long as the sealing bar plus about 5 cm (± 2 inches).

12. Stick the new teflon tape straight over the new sealing wire (wires). Ensure that the teflon is

straight on the sealing bar and that the sticky part is stuck on the side. Ensure that the teflon

is stuck on the bar smoothly and without folds.

13. Cut the teflon tape off so that the sticky part does not get stuck on the sides of the clamps but

that the teflon extends over the top of the clamps.

14. Place the sealing bar back in the machine. Ensure that the sealing beam is properly clicked

onto the holders or that the screws are firmly screwed in.

See page 29

for correct parts and quantities

Pull wires taught using a

air of pliers and a vice

and screw the wires down

on the clamping plate.

Remove teflon ta

Unscrew and remove

sealing wires

lace the teflon ta

Screw down new wires

onto clamping plate

Cut off the ends of the sealing wire and stick

Teflon tape over the sealing beam without folds

Special remark bi-active sealing system

The sealing wire must be accurately placed on the upper

and lower beams so that the sealing wires line up with

each other exactly during sealing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman POLAR Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman POLAR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info