Bedienungsanleitung Hertz hp 1 d (Seite 22 von 34) (Englisch)

167907

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

1 2

HP 1D HP 1D

HP 1KD HP 1KD

Input Panel

HP 1D - HP 1KD

1_ PRE IN: Preamplified inputs Right (R) and Left (L). Connect the outputs from the preamplified

section of the head unit or of an external electronic crossover. You can use either input or both as

the amplifier performs the channels MIX to drive the amplifier in mono.

2_ PRE OUT: Preamplified outputs Right (R) and Left (L). The signal available on the output can be

filtered. It outputs the PRE IN input signals. If the amplifier is driven by a stereophonic signal, the

latter will be on these outputs.

3_ SPEAKER IN: Amplified signals inputs Right (R) and Left (L). Connect the outputs from the

head unit amplified section. You can use either input or both as the amplifier performs the

channels MIX to drive the amplifier in mono.

CAUTION: Use this input only with sources equipped with bridged output (BTL).

4_ HP RVC: Input for the supplied digital Remote Volume Control connector. This system controls

the Sub volume remotely.

HP 1D

5_ HP LINK: Section of inputs/outputs for bridge connection between two amplifiers to increase

the amplifiers total power.

HP 1KD

6_ HP LINK 2: Connector for bridge connection between two amplifiers to increase the amplifiers

total power.

7_ HP RBC: Supplied Remote Bass Control connector input. This system equalizes the ultralow range.

Power Supply/Outputs/Other Functions Panel

HP 1D - HP 1KD

1_ + BATT (11÷16.5 VDC): terminal block through the fuse holder supplied for the amplifier power

supply positive pole connection. The hole accepts cables up to 2 A.W.G. For the best current

transfer, we recommend the use of cables with as big a section as possible or, at least, with the

same section as the wire connected to the negative pole.

CAUTION HP 1KD: Connect both power supply terminal blocks, inserting the fuse holder

supplied with its fuse, in the battery positive pole, to achieve the best performance and avoid

to damage the amplifier.

2_ GND: terminal block for the amplifier power supply negative pole connection. Insert the battery

negative cable or a wire connected to the vehicle chassis here. The hole accepts cables up to 2

A.W.G. For the best current transfer, we recommend the use of cables with as big a section as

possible or, at least, with the same section as the wire connected to the positive pole;

CAUTION HP 1KD: Connect both terminal blocks to ground or to the battery negative pole.

3_ REM: terminal for the Remote cable coming from the device which turns on the amplifier.

Voltage must be between 7 and 16,5 VDC.

4_ SPEAKER A: Speaker + and – power terminal; signal is MONO. The hole accepts cables up to

10 A.W.G.

5_ SPEAKER B: Speaker + and – power terminal, outputs are connected inside in parallel with A

SPEAKER to allow the connection of several speakers. The hole accepts cables up to 10 A.W.G.

Italiano | English

42 43

manuale HP_ita_ing 7-12-2007 17:58 Pagina 43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hertz hp 1 d Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info