Bedienungsanleitung Hertz hp 5 (Seite 19 von 28) (Englisch)

167984

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

1 3

HP 5 HP 5

456

Input Panel

1_A PRE IN: A channels preamplified inputs Right (R) and Left (L).Connect the outputs from the

preamplified section of the head unit or of an external electronic crossover.

When using HP 5 in 3 CH mode the A PRE IN drives both A & B channels outputs.

2_B PRE IN: B channels preamplified inputs Right (R) and Left (L).Connect the outputs from the

preamplified section of the head unit or of an external electronic crossover.

3_C PRE IN: C channel preamplified inputs Right (R) and Left (L).Connect the outputs from the

preamplified section of the head unit or of an external electronic crossover. You can use either

input or both as the amplifier performs the channels MIX to drive the C channel in mono.

4_A SPEAKER IN: A channels amplified signals inputs Right (R) and Left (L). Connect the outputs

from the head unit amplified section. When using HP 5 in 3 CH mode the A SPEAKER IN drives

both A & B channels outputs.

5_B SPEAKER IN: B channels amplified signals inputs Right (R) and Left (L). Connect the outputs

from the head unit amplified section.

6_C SPEAKER IN: C channel amplified signals inputs Right (R) and Left (L). Connect the outputs

from the head unit amplified section. You can use either input or both as the amplifier performs

the channels MIX to drive the C channel in mono.

CAUTION: Use SPEAKER IN input only with sources equipped with bridged output (BTL).

7_ HP RVC: Supplied Remote Bass Control connector input. This system equalizes the ultralow range.

Power Supply/Outputs/Other Functions Panel

1_ + BATT (11÷15 VDC): terminal block through the fuse holder supplied for the amplifier power

supply positive pole connection. The hole accepts cables up to 3 A.W.G. For the best current

transfer, we recommend the use of cables with as big a section as possible or, at least, with the

same section as the wire connected to the negative pole.

2_ GND: terminal block for the amplifier power supply negative pole connection. Insert the battery

negative cable or a wire connected to the vehicle chassis here. The hole accepts cables up to

3 A.W.G. For the best current transfer, we recommend the use of cables with as big a section as

possible or, at least, with the same section as the wire connected to the positive pole;

3_ REM: terminal for the Remote cable coming from the device which turns on the amplifier.

Voltage must be between 7 and 16,5 VDC.

4_ A CH SPEAKER OUTPUT: A channels speaker Right (R) and Left (Left) power terminals. The

hole accepts cable up to 10 A.W.G. When using HP 5 in 3 CH mode the output is available at

terminals L+ and R- (3CH LEFT).

5_ B CH SPEAKER OUTPUT: B channels speaker Right (R) and Left (Left) power terminals. The

hole accepts cable up to 10 A.W.G. When using HP 5 in 3 CH mode the output is available at

terminals L+ and R- (3CH RIGHT).

6_ C CH SPEAKER OUTPUT: C channel speaker + and - (Left) power terminals. The hole accepts

cable up to 10 A.W.G. Signal at C speaker output is mono.

Italiano | English

36 37

Manuale HP5 13-07-2007 17:35 Pagina 37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hertz hp 5 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info