Bedienungsanleitung Hifonics Brutus BRX (Seite 4 von 18) (Englisch)

505731

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AMPLIFIER FEATURE DESCRIPTIONS

BRUTUS BRX AMPLIFIERS:

A POWER LED indicates the powered up and turned on condition.

Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the

All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and

mono amps which are capable of 4, 2 and 1-Ohm loads.

amplifier DC faults indicated by the red “PROTECT” LED.

Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers.

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU WILL

The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel amplifiers

CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE WARRANTY

and 0.2V to 9V for the mono models.

All crossovers are fully variable in their respective ranges.

PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4 and 2-Ohms wired

Crossover filters are 12dB/Octave.

stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2 and 1-Ohm.

1 set for channels 1 & 2.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

-HPF: Selects the built in HI PASS filter.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS filter.

MODE: Selectable Stereo or MONO operation.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain

multiple amplifiers from one signal.

HPF: Variable low frequency cut off from 60Hz to 1.3kHz.

LPF: Variable high frequency cut off from 30Hz to 250Hz.

BASS EQ: 45Hz bass boost variable from 0dB to 12dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

Note that the LOW PASS signal is MONO.

-In the LPF position, the HPF filter acts as a subsonic filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS EQ is also switched in.

BRX160.2 2-CHANNEL AMPLIFIERS

LINE OUT LINE INPUT LEVEL BASS EQ X-OVER HPF LPF MODE

6V 0.2V 0dB 12dB 60Hz 1.3kHz 30Hz 250Hz

PROTECT

POWER

FULL LPF HPF

MONO STEREO

The 4 channel amps have the same features as the 2 channel models except that there are 2 sets of

controls.

1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch which allows you to select 2 or 4 channel operation.

Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically

supply signal to channels 3/4. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.

LOW PASS: Variable high frequency cut off from 30Hz to 150Hz.

BASS EQ: 45Hz bass boost variable from 0dB to 10dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

The 5 channel amps have the same features as the 4 channel models except that there are 3 sets of

controls.

1 set for channels 1 & 2, 1 set for channels 3 & 4 and 1 set for channel 5.

In addition, the 4 channel models have a Mode switch which allows you to select 2, 4 or 5 channel operation.

Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically

supply signal to channels 2/4/5. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4 and

signal will be internally routed to Ch5. Select 5 if you are supplying RCA’s to each INPUT.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.

LOW PASS: Variable high frequency cut off from 30Hz to 150Hz. (CH3/4 & 5)

BASS EQ: 45Hz bass boost variable from 0dB to 10dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

REMOTE: This is a remote input jack for the remote level control on Ch5.

Note that the LOW PASS signal is MONO.

-In the LP/BP position, the HI PASS filter acts as a subsonic filter.

-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz, BASS EQ is also switched

in.

Note that the LOW PASS signal is MONO.

-In the LP position, the HI PASS filter on Ch3/4 acts as a subsonic filter.

BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIERS

BRX5000.5 5-CHANNEL AMPLIFIERS

CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT

10Hz 1.5kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V

LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL

PROTECT

2CH 4CH

HI FULL LP/BP

SUBSONIC: Crossover filter from 15Hz to 35Hz.

LOW PASS: Crossover filter from 35Hz to 250Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 9 volts.

BASS EQ: Adjustable bass boost from 0db to 10dB.

PHASE:

REMOTE: This is the input jack for the remote Level control.

BALANCED INPUT:

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain

multiple amplifiers from one signal.

The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time

alignment.

Accepts line level balanced input from 0.4v to 18v.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the settings on the

amplifier simplifying daisy chaining of amplifiers.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the amp not covered in the

warranty.

BRX1100.1D / BRX1600.1D / BRX2000.1D MONO BLOCK AMPLIFIERS

INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS

L L

R R

SUB

POWER

PROTECT

BALANCED

9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz

The BRX2400.1D is identical to the other BRX mono amplifiers except that the BRX2400.1D is a

linkable amplifier and features a MASTER / SLAVE selection switch and IN / OUT RCA connection. This

allows for a pair of amps to link at 2-Ohms and produce 4800 watts rms.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the amp not covered in the

warranty.

BRX2400.1D MONO BLOCK AMPLIFIERS

INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS

L L

R R

SUB

OUT

POWER

PROTECT

OUTPUT

MASTER

INPUT

SLAVE

BALANCED

9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz

LINE INPUT CH1/2 X-OVER HI PASS LEVEL HI PASS CH3/4 X-OVER LOW PASS LEVEL

10Hz 1.5kHz 6V 0.2V 10Hz 1.5kHz 30Hz 150Hz 6V 0.2V

30Hz 150Hz 0dB 10dB 6V 0.2V POWER

REMOTE LOW PASS BASS EQ LEVEL CH5 MODE

PROTECT

Ch2

Ch5

Ch4

Ch3Ch1

HI FULL

HI FULL LP

2CH 4CH 5CH

Hifonics Brutus BRX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info