Bedienungsanleitung Hifonics BRX4000D (Seite 20 von 32) (Deutsch, Englisch)

700129

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

FUNCTIONAL INSTRUCTIONS

FEATURES AND OPERATIONAL CONTROLS

The optional BALANCED INPUT is unlike the regular RCA-cables insusceptible against interspersion and interferences of the

vehicle’s electronics. You need therefor a Balanced-Line-Transmitter with a special cable, which can be connected between the

head unit and the amplier. The Balance-Line-Transmitter is not included in delivery. Refer to the further information on page 29.

Never use the BALANCED INPUT and the RCA jacks LINE IN at the same time.

The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.

1 76 104 9 113 85

POWER INPUT

SPEAKER OUTPUT

PROTECT

POWER

SLAVEMASTER

LEVEL

BASS LEVEL

CONTROLLER

AUTO TURN ON

(ONLY IN HI LEVEL INPUT MODE)

0dB 18dB

LINE IN SLAVE IN/OUT

LEVEL

INPUT

MODE

35Hz 250Hz

MIN MAX

OFF

LOW

SUB

BOOST

Q-CONTROLPHASE

FREQ.

RANGE

SUB SONIC

15Hz 55Hz

GND +12VREM

EXTENDED BASS CONTROL

WIDE NRW20Hz 80Hz

0° 180°

BALANCED

INPUT

BRX4000 D

BLUE / WHITE

LOG0

2 12

SPEAKER CABLES

SHIELD

TO THE LINE IN ON THE

AMPLIFIER

CORE CONDUCTOR

HI LEVEL INPUTS & AUTO TURN ON

If your head unit has no pre-amplier low level RCA outputs or doesn’t provide a separate remote turn on wire (like described on

page 19/#2), follow these instructions:

AUTO TURN ON

Bring the AUTO TURN ON switch to position ON to activate the auto turn on function. This function only works, if the push button

INPUT LEVEL MODE is in HI position and highlevel inputs (speaker outputs from the headunit) are connected at the LINE IN.

Please check the regarding notes below.

The amplier detects now by the so called ”DC Offset” (a voltage increase to 6 volts on the high level speaker outputs) if the

head unit is turned on and the amplier turns automatically on. As soon as the head unit is turned off, the amplier shuts down

automatically after approx.one minute.

NOTE: The AUTO TURN ON usually works with 90% of all headunits, because they are equipped with the ”High Power” outputs.

Only with a few older headunits the AUTO TURN ON function is not applicable.

The port of the remote connector of the amplier (page 19#2, REM) can now be used also to turn on additional other ampliers.

Connect the REM ports of the ampliers and ensure, that the other amplier’s AUTO TURN ON function is deactivated.

High level speaker cables as signal input:

Please use the optional HF-HLA adaptor from HiFonics (see

page 29). This adaptor is optmized for the use with this amplier

inputs and owns additionally a protect function for the speaker

outputs of your headunit.

Alternative: Solder the ends of the loudspeaker cables of the

head unit with common RCA connectors (separately available)

and connect them with LINE IN of the amplier.

The HI LEVEL INPUTS can be use independently from the AUTO

TURN ON function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics BRX4000D Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info