Bedienungsanleitung Hifonics bxi2000d (Seite 20 von 28) (Deutsch, Englisch)

495757

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

PROTECT

BRIDGE

WHITE

LOGO

BADGE

BLUE

FUSE

GNDBATT +12V REM

SPEAKER OUTPUT

+ –+ –

POWER INPUT

BXi1000D · BXi1500D · BXi2000D · BXi3000D · BXi4000D · BXi6000D

MODE

BXi 4000D

1x 2000 Watts

SLAVE IN/OUT

MASTERSLAVE

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.

If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.

• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + / -) by using appropriate wires.

• Ensure by any means, that the total impedance load of subwoofer is not lower than 1 ohm. Too low impedance cause high

temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

MODE SWITCH

• The MODE switch must be in Position MASTER.

LEVEL CONTROLLER

• Turn the LEVEL controller of the amplifier to the 6V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

EXTENDED BASS CONTROL

• The SUB BOOST controller adjusts the bass enhancement between 0db and +18dB.

• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.

Use this controller carefully!

• Attend therefor the further information (EXTENDED BASS CONTROL) on page 19 (Section #5).

LOW PASS CONTROLLER

• The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously

adjustable from 35 Hz to 250 Hz.

SUB SONIC CONTROLLER

• The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid a

mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on the size

of the subwoofer.

PHASE CONTROLLER

• The PHASE controller allows to adjust the phasing between 0° and 180°.

Thereby you are able to adjust the subwoofer perfect to the vehicle’s acustics.

BASS REMOTE

• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver’s seat.

Please use only the enclosed bass remote controller and cable.

INTERCONNECTION EXAMPLE Low Pass-Mode (Standard Subwoofer Operation)

Connect the bass remote

controller and the

remote terminal on the amplifier

with the enclosed cable.

Connect stereo RCA output

(R/L or SUB OUT)

of the headunit with

LINE INPUT R/L of the amplifier

R L

Subwoofer

1 – 8 Ohms

Switch setting =

MASTER

A additional subwoofer can be

connected to the non-occupied

speaker outputs. In this case

ensure a impedance of 2 - 8 ohms

per subwoofer.

NOTE!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics bxi2000d Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info