Bedienungsanleitung Hifonics HFi (Seite 4 von 15) (Englisch)

505737

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

AMPLIFIER FEATURE DESCRIPTIONS

HFi AMPLIFIERS:

! Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation ! All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,

and amplifier DC faults indicated by the red “PROTECT” LED.

except the mono amps which are capable of 4, 2 and 1-Ohm loads.

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU

Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable

WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE

amplifiers.

! The input sensitivities for rated output powers are variable from 0.2 volts to 6 volts.

WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4

! All crossovers are fully variable in their respective ranges.

and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2

! Crossover filters are 12dB/Octave.

and 1-Ohm.

! A POWER LED indicates the powered up and turned on condition.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER

setting simplifying daisy chaining of amplifiers.

-SUBSONIC: Allows you to adjust the crossover filter from 15Hz to 35Hz.

-LPF: Allows yo to adjust the LOW PASS crossover filter from 30Hz to 250Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.

BASS EQ: The Bass EQ is adjustable from 0db to 10dB.

REMOTE: This is the input jack for the remote Level control.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the

amp not covered in the warranty.

HFi1000D / HFi1500D / HFi2000D / HFi2500D MONO BLOCK AMPLIFIERS

OUTPUT INPUT

L L

R R

POWER

PROTECT

6V 0.2V 0dB 10dB 15Hz 35Hz 30Hz 250Hz

LEVEL BASS EQ REMOTE SUBSONIC LOW PASS

The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of

controls.

1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch which allows you to select 2, 3 or 4 channel

operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically

supply signal to channels 3/4. Select 3 channel when you only have RCA’s in CH 1/2 but plan to run

channels 3/4 bridged. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting

simplifying daisy chaining of amplifiers.

-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 12kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.

MODE: The mode switch allows you to choose Stereo for full range 2 channel operation or MONO

for bridging operation

HIGH INPUT: If your radio/CD player does not have unbalanced (RCA) outputs, you can use the

HIGH level (wire) inputs.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

Note that the LOW PASS signal is MONO.

-In the LPF position, the HIGH PASS filter acts as a subsonic

filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS

-EQ is also switched in.

HFi55.4 / HFi100.4 4-CHANNEL AMPLIFIERS

LINE OUTCH3/4 CH1/2

L L

R R

6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz

LEVEL BASS EQ X-OVER HPF LPF

6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz 2 3 4

LEVEL BASS EQ X-OVER HPF LPF MODE

POWER

PROTECT

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting

simplifying daisy chaining of amplifiers.

-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 12kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.

MODE: The mode switch allows you to choose Stereo for full range 2 channel operation or MONO

for bridging operation

HIGH INPUT: If your radio/CD player does not have unbalanced (RCA) outputs, you can use the

HIGH level (wire) inputs.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

Note that the LOW PASS signal is MONO.

-In the LPF position, the HIGH PASS filter acts as a subsonic

filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS

-EQ is also switched in.

HFi100.2 2-CHANNEL AMPLIFIERS

OUTPUT INPUT

L L

R R

6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz MONO STEREO

LEVEL BASS EQ X-OVER HPF LPF MODE

POWER

PROTECT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics HFi Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info