Bedienungsanleitung Hifonics rx 8407 (Seite 10 von 16) (Deutsch, Englisch)

165104

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Battery

Ground

FUSE

Fuse

Remote

General Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be

sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you

should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable installation. It is also important to

ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do not install the amplifier on a subwoofer box

or on vibrating parts of the vehicle, since the vibrations can cause damage to the amplifier´s electrical components.

Installation of the amplifier

At first you have to pull out the screws of the cover of the amplifier. Then you

are abel to remove the cover and now you can mark the location for the mounting

screw holes by using the amplifier as a template. Drill holes at the marked locations

and firmly fasten the amplifier in place with the mounting screws supplied in the

accessory kit. Before drilling or cutting any holes, investigate the layout of your

automobile thoroughly:

Take care when working near the gas lines or hydraulic lines and

electrical wiring of your car.

Electrical Connection

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle´s chassis.

The best method is to use a threading sheet metal screw since the threads cut into

bare metal. Ensure that all paint or other insulation is removed from around the hole area,

and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use

as short a piece of cable as possible - use the same gauge that is used for the +12V cable.

Make sure that the connection is safe, a loose connection may result in amplifier noise and fault condition.

Remote (REM)

Many music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio doesn't have a remote

turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the power antenna retracts

when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-on.

Battery Connection (+12V)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse in

line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (16 - 25 mm²). This connection must be

completed using spade lug with insulating sleeve.

Fuses

The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance)

of the speakers, for 2 Ohm loads the fuses may have to get increased in case of higher power consumption.

Power / Ground / Remote Connection

INSTALLATION & ELECTRICAL CONNECTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics rx 8407 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info