700161
15
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
Before you start with the installation of the sound system, disconnect by any means the GROUND connection
wire from the battery, to avoid any risk of electric shock and short circuits.
REFERENCE NOTE
INSTALLATION INSTRUCTIONS|ENG
15
MECHANICAL INSTALLATION
Avoid any damage removing of the components of the vehicle like wires, cables, board computer, seat belts, gastank or the like.
Ensure that chosen location provide sufficient air circulation for the amplifier. Do not mount the device into small or sealed spaces without
air circulation near by heat dispersing parts or electrical parts of the vehicle.
Do not mount the amplifier on top of a subwooferbox or any other vibrating parts, thereby parts in the inside of the amplifier may get loosen.
The wires and cables of power supply and the audio signal must be as short as possible, to avoid any losses and interferences.
Vehicle
1
On each corner of the amplifier you find
mounting openings for fixing the amplifier
into your vehicle. These openings are
covered by cover screws, which have to
be removed before.
Please ensure during the installation, that
you don’t scratch or damage the amplifier
surface with the tools.
Marking
Amplifier
Cover screw
After removing the cover screws, uphold
the amplifier to the chosen mounting
location in the vehicle. Then mark the four
drill holes with an appropriate pen or
peening tool through the mounting
openings.
Observe that enough space remains for
the installation of the cables and ensure
that they will not be bended and have
sufficient pull relief.
Amplifier
Pen or
peening tool
2
Vehicle
Put the amplifier aside and then drill the
four holes for the mounting screws at the
before marked locations.
Please ensure not to damage any
components of the vehicle while drilling
the holes. Alternatively (depends on the
material of the surface) you can also use
self-tapping screws.
Drill (Ø 2 mm)
3
Vehicle
Then uphold the amplifier to the chosen
position and fix the screws through the
holes of the mounting brackets into the
drilled screwholes.
Ensure that the mounted amplifier is fixed
tight and not get loosen.
Then screw back the cover screws into
the mounting opening.
Mounting screw
4
If you own another HiFonics TRITON
amplifier, you are able to mount the two
amplifiers over eachother.
After installing ”Amplifier 1”, follow the
”Section 1” for ”Amplifier 2” like decribed
above.
Then put ”Amplifier 2” carefully onto the
designated sockets of ”Amplifier 1”.
Please ensure during the installation, not
to damage the amplifier surface.
5
Amplifier 1
Amplifier 2
Screw both amplifiers together by using
the four provided binding screws inside
the mouting openings.
Ensure that the mounted amplifier is fixed
tight and not get loosen.
Then screw back the cover screws into
the mounting opening.
6
Amplifier 1
Amplifier 2
Binding
screw
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics Triton IV wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info