Bedienungsanleitung Hifonics TRX6006 DSP (Seite 36 von 40) (Deutsch, Englisch)

700123

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

TROUBLE SHOOTING

Malfunction: no function

Reason: Remedy:

1. The power supply connection of the device is not correct Recheck

2. The cabels have no mechanical or electrical contact Recheck

3. The remote turn-on connection from the head unit to the amplier is not correct Recheck

4. Defective Fuses. In case of replacing the fuses, ensure the correct fuse rating Replace Fuses

Malfunction: no signal on loudspeakers, but power LED lights up

Reason: Remedy:

1. The connections of the speakers or the RCA audio cables are not correct Recheck

2. The speaker cables or the RCA audio cables are defective Replace cables

3. The loudspeakers are defective Replace speakers

4. HP controller in LP/BP operation is adjusted to high Turn down controller

5. No signal from the head unit Check head unit settings

6. A wrong input source under INPUT SOURCE is selected, which is not connected (e.g. AUX IN) Check selection

7. For example on one or more channels „Mute“ is activated in the DSP software. Check settings

8. The volume level on the remote controller is adjusted too low Turn up the volume level on the remote

Malfunction: one or more channels or controllers are without function / faulty stereo stage

Reason: Remedy:

1. The balance or fader controller of the head unit is not in the center-position Turn to center-position

2. The connections of the speakers are not correct Recheck

3. The loudspeakers are defective Replace speakers

4. HP controller in LP/BP operation is adjusted to high Turn down controller

5. For example on one or more channels „Delay“ or „Phase“ is incorrectly set in the DSP software. Check settings

Malfunction: distortions on the loudspeakers

Reason: Remedy:

1. The loudspeakers are overloaded Turn down the level

Turn down the level on the head unit

Switch off loudness on the head unit

Reset bass EQ on the head unit

Malfunction: no bass or stereo sound

Reason: Remedy:

1. Interchange of loudspeaker cable polarity Reconnect

2. The RCA audio cables are loose or defective Reconnect or replace the cables

3. For example on one or more channels „Delay“ or „Phase“ is incorrectly set in the DSP software. Check settings

Malfunction: amplier runs into protection mode (red protection LED lights up)

Reason: Remedy:

1. Short circuit on the loudspeakers or cables Reconnect

2. Overheated by too low speaker impedance Choose a higher impedance

Use a new speaker setup

3. Insufcient air circulation by a inappropriate mounting position of the amplier Change the mounting position

Ensure air circulation

4. Overloaded by insufcient power supply (too small prole section on the power cables) Use a bigger prole section

Malfunction: hiss or white noise on the loudspeakers

Reason: Remedy:

1. The level controllers in the DSP software are turned up to loud Turn down the level

2. The treble controller on the head unit is turned up Turn down the level on the head unit

3. The speaker cables or the RCA audio cables are defective Replacing the cables

4. The hissing is caused by the head unit Check the head unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics TRX6006 DSP Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info