Bedienungsanleitung Hifonics TSi1000-I (Seite 18 von 28) (Deutsch, Englisch)

700153

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENG|INSTALLATION INSTRUCTIONS

ELECTRICAL INTERCONNECTION

GND

Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short

as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable

and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if

possible and enforce it, if required. Use a ground wire with a sufficient cross section (at least 20 mm

) and the same size like the

plus (+12V) power supply wire.

REM

Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the

amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm

). Thereby the amplifier will turn on or off automatically

with your headunit.

If your headunit doesn’t provide a separate remote turn on wire and has no pre-amplifier low level RCA outputs, please refer to

the section AUTO TURN ON on the following page.

+12V

Connect the +12V-terminal with the +12V pole of the vehicle’s battery. Use therefor a suitable cable with a sufficient cross section

(at least 20mm

) and install a additional in-line fuse. For safety reasons the distance between the fuseblock and the battery must

be shorter than 30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.

LOGO BADGE

This switch changes the illumination color of the upper logo badge (blue or white). Follow by any means the directives of your

national road traffic regulations.

FUSE

The inserted fuses protect the amplifier from shorts and capacity overload. Replace damaged fuses only with equal fuses with

the same fuse rating (check the specifications).

BEFORE THE CONNECTION

For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient

profile section (at least 20 mm

), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and

remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are

fixed tight after the installation, because loosely connections may cause malfunctions, insufficient power supply or interferences.

421 3 5

Installation of RCA/Audio signal cables and power supply.

Ensure while installation not to lead the audio cables between the headunit and the amplifier together with the power supply wires

on the same side of the vehicle. The best is a areal separated installation in the left and right cable channel of the vehicle. Therewith

a overlap of interferences on the audio signal will be avoided. This stands also for the equipped bass-remote wire, which should be

installed not together with the power supply wires, but rather with the audio signal cables.

REFERENCE NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics TSi1000-I Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info