Bedienungsanleitung Hifonics TSi600-IV (Seite 22 von 28) (Deutsch, Englisch)

700157

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE IN CH 1 and CH 2 of the amplifier with appropriate high-value

RCA cables. If a separate SUB OUT from your headunit is available, use this as LINE OUT.

• Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.

• Ensure by any means, that the total impedance load of all subwoofers per channelpair is not lower than 4 ohms. Too low impedance

cause high temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

INPUT SWITCH

• Select the 4CH position on the INPUT switch.

CROSSOVER SETTINGS CH3/4 (SUBWOOFER 1 & 2)

• In the mono/subwoofer mode the X-OVER MODE switch must set to the LPF/BPF position (Lowpass/Bandpass mode), thereby the

higher frequencies will be eliminated. The cut-off frequency ist adjustable with the LPF controller and should be set between

60 to 100 Hz, depending on the size of the subwoofer.

• In the lowpass mode the HPF controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and harmful

frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 40 Hz, depending

on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.

CROSSOVER SETTINGS CH1/2

• Set the X-OVER MODE switch to DUPE. The DUPE mode passes (duplicate) the signal from CH3/4 to the line input section of CH1/2.

All controllers and settings are without function. The LINE IN RCAs of CH1/2 are deactivated.

LEVEL CONTROLLER CH3/4

• Turn the LEVEL controller of the amplifier to the MIN. position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

BOOST CONTROLLER CH3/4 (SUBWOOFER 1 & 2)

• The BOOST controller adjusts the bass enhancement between 0db and +12dB @ 50 Hz. In the DUPE-mode the boost controller also

affects the bass enhancement on the channel pair CH1/2 (Subwoofer 1).

• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.

Use this controller carefully!

REMOTE BASS LEVEL CONTROLLER BLC-TSi

• The enclosed remote BASS LEVEL Controller BLC-TSi adjusts the bass-level e.g. from the driver’s seat.

In the DUPE-mode the bass level controller also affects the bass level on the channel pair CH1/2 (Subwoofer 1).

Please use only the enclosed controller and cable.

INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged

ENG|OPERATIONAL INSTRUCTIONS

INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged

BLC-TSi

Subwoofer 2

4 – 8 Ohms

Subwoofer 1

4 – 8 Ohms

R L

Connect RCA output (L/R or SUB OUT)

of the headunit with the LINE IN CH3/4 of

the amplifier

Position XOVER MODE:

LPF/BPF

Position

XOVER MODE:

DUPE

Position

INPUT: 4 CH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics TSi600-IV Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info