Bedienungsanleitung Hifonics X4-Andromeda (Seite 20 von 28) (Deutsch, Englisch)

700150

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WHITE

BLUE

BATT +12V

GND

REM

FUSE

POWER INPUT

LOGO BADGE

SPEAKER OUTPUT

MONO BRIDGED

– CH4 + – CH3 +

MONO BRIDGED

– CH2 + – CH1 +

REMOTE

CH1

CH2

CH3

CH4

LINE INPUTS

CH1/2

CH3/4

BALANCED

INPUTS

STEREO

MONO

12dB

24dB

INPUT MODE

4CH 2CH

LOW PASS

HIGH PASS

X-OVER MODE CH1/2

X-OVER MODE CH3/4

LP/BP FULL HP

POWER

PROTECT

BASS BOOST

LEVEL

CH1/2 CH1/2

CH3/4 CH3/4

LINE OUTPUT

SUMMED CH1/2/3/4

FULL RANGE

OPERATING INSTRUCTIONS

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.

• Connect the front- and rear speakers with the speaker outputs (SPEAKER OUTPUT + 1CH -, + 2CH - and + 3CH -, + 4CH -).

• Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature

and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

INPUT MODE SWITCH

• Select the 4CH position on the INPUT MODE switch. If there is only one RCA stereo audio cable from the headunit available, connect

the CH1/2 RCA line inputs and select the 2CH position.

CROSSOVER SETTINGS CH1/2 & CH3/4

• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).

• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage

by lower frequencies on the speakers. The cut-off frequency is adjustable with the HIGH PASS controller and should be set between

60Hz to 150Hz, depending on the size of the speakers.

• The LOW PASS Controller is not in use in this interconnecting example.

LEVEL CONTROLLER CH1/2 & CH3/4

• Turn the LEVEL controller of the amplifier to the 9V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

BASS BOOST CONTROLLER

• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .

BASS REMOTE

• The enclosed BASS REMOTE Controller is not in use in this interconnecting example.

INTERCONNECTION EXAMPLE: 4-Channel Mode 2 x Stereo System (Front & Rear)

Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity

of all connections. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

REFERENCE NOTE

RR RL

Connect the stereo RCA output (FL/FR & RL/RR)

of the headunit with LINE INPUTS

CH1/2 and CH3/4 of the amplifier

Loudspeaker

front / left

1 – 8 Ohms

Loudspeaker

front / right

1 – 8 Ohms

FL FR

Loudspeaker

rear / left

1 – 8 Ohms

Loudspeaker

rear / right

1 – 8 Ohms

Switch position CH1/2 = HP or FULL

and CH3/4 = HP or FULL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics X4-Andromeda Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info