Bedienungsanleitung Hifonics X4-Andromeda (Seite 25 von 28) (Deutsch, Englisch)

700150

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

PROTECTION CIRCUIT

This amplifier owns a protection circuit. If overloading, overheating and shorted loudspeakers, or too low impedance

is insisted, the amplifier shuts down to prevent serious damage. If one of this disfunctions is detected, the red PROTECT

LED lights up.

Check in this case all connections to detect short-circuits, faulty connections or overheating. Attend the regarding notes

on the previous page.

If the reason for the disfunction is eliminated, the amplifier is ready for operation again.

If the red PROTECT LED does not stop to light up, a damage on the amplifier is insisted. In this case return the amplifier

to your car audio retailer with a detailled malfunction description and a copy of the proof of purchase.

WARNING: Never open the amplifier and try to repair it by yourself. This causes a loss of warranty. The repairing

service should be made only by skilled technicians.

REFERENCE NOTE

ELECTRICAL INTERFERENCES

The reason for interferences are mostly the passed cables and wires. Especially the power and audio cables (RCA)

of your sound system are vulnerable. Often these interferences are caused by electric generators or other electrical

units (fuel pump, A/C etc.) of the car. The most of these problems can be prevented by a correct and careful wiring.

Here are some courtesy notes:

1. Use only double or triple shielded audio RCA cables for the connection between the amplifier and headunit. A useful

alternative are represented by anti-noise-devices or additional ancillary equipment like Balanced Line Transimtters,

which you can purchase at your car audio retailer. If possible do not anti-noise-filters, which are splicing the ground

of the RCA audio cables.

2. Do not lead the audio cables between the headunit and the amplifier together with the power supply wires on the

same side of the vehicle. The best is a areal separated installation in the left and right cable channel of the vehicle.

Therewith a overlap of interferences on the audio signal will be avoided. This stands also for the equipped bass-

remote wire, which should be installed not together with the power supply wires, but rather with the audio signal

cables.

3. Avoid ground loops by connecting all ground connections in a starlike arrangement. The suitable ground center

point is ascertainable by measuring of the voltage directly on the vehicle’s battery by a multi-meter. You should

measure the voltage with turned-on inginition (acc.) and with other turned-on power consumers (e.g. headlights, rear

window defroster, etc,).Compare the measured value with the voltage of the ground point you have choosen for the

installation and the positive pole (+12V) of the amplifier. If the voltage has just a little difference, you have found a

suitable ground point. Otherwise you need to choose a other ground point.

4. Use if possible only cables with added or soldered cable sockets or the like. Gold plated or high value nickel plated

cable sockets are corrosionfree and own a very low contact resistance.

REFERENCE NOTE

TROUBLE SHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics X4-Andromeda Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info