700148
21
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
Switch position = LP
21
OPERATING INSTRUCTIONS
INTERCONNECTION EXAMPLE: Master/Slave Mode
MASTER/SLAVE-Mode
NOTE: The GENERATION X4 Master/SLAVE-Mode only works with two similar X4-Amplifier-Models.
INTERCONNECTION MASTER
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
Connect the remote wire (REM) to the remote terminal (REM) of the MASTER amp.
If required connect the enclosed bass remote wire only on the REMOTE IN port of the MASTER amp.
Don’t use the REMOTE OUT port in MASTER/SLAVE mode.
INTERCONNECTION SLAVE
Connect the RCA jacks SLAVE IN/OUT of the MASTER amp with the RCA jacks SLAVE IN/OUT of the SLAVE amp with appropriate
high-value RCA cables.
Connect the remote wire (REM) of the remote terminal (REM) of the MASTER amp with the remote terminal (REM) of the SLAVE amp.
Use therefore cable with a minimum profile section of 0,5 mm
2
.
• Connect the PROTECT BRIDGE port of the MASTER amp with the PROTECT BRIDGE port of the SLAVE amp with the enclosed
PROTECT BRIDGE wire.
INTERCONNECTION SUBWOOFER
• Check page 22.
SETTINGS MASTER
• The OPERATION MODE switch should be in LP position.
Please note the information of LOW PASS, SUB SONIC, PHASE, LEVEL, SUB BOOST, FREQ RANGE, Q-CONTROL and BASS
REMOTE on page 20.
SETTINGS SLAVE
• The MODE switch must be in SLAVE position.
In the SLAVE mode all controllers of the SLAVE amp are without function.
Only the already modified audiosignal of the MASTER amp will be amplified.
1. Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of the
MASTER amp
Connect the bass remote controller
and the remote terminal on the
MASTER amplifier (REMOTE IN)
with the enclosed cable .
Switch position = MASTER
SLAVE
MASTER
Switch position = SLAVE
Remote wire REM Remote wire REM
Protect Bridge wire
Remote wire REM
2. Connect Stereo RCA output (MASTER OUTPUT)
of the MASTER amp with the SLAVE INPUT of the
SLAVE amp
1.
2.
Protect Bridge wire
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics X4-Atlas wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info