Bedienungsanleitung Hifonics X4 (Seite 16 von 24) (Deutsch, Englisch)

700147

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

INSTALLATION INSTRUCTIONS

ELECTRICAL INTERCONNECTION

Installation of RCA/Audio signal cables and power supply.

Please install if possible the audio cables from the headunit and the amplifier not together with the power

supply wires on the same side of the vehicle. The best is an areal separated installation in the left and right

cable channel of the vehicle. This avoids an overlap of interferences on the audio signal. This also applies

for the supplied bass-remote connection, which should not be installed together with the power supply

wires. It is recommended to use the same side like the audio cables.

REFERENCE NOTE

BATT+12V

Connect both BATT+12V-terminals with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufficient cross section

and install an additional in-line fuse. For safety reasons the distance between the fuseblock and the battery must be shorter than

30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.

GND

Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short

as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable

and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if

possible and enforce it, if required.

REM

Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the

amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm

). Thereby the amplifier will turn on or off automatically

with your headunit.

LOGO BADGE

With this switch you can choose between white or blue illumination of the upper logo badge.

Always follow the guidelines of your national road traffic regulations.

BEFORE THE CONNECTION

For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient

profile section (attend the specifications below), the suitable fuse rating and the conductivity of the cables when you purchase your wiring

kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that

all screws are fixed tight after the installation, because loosely connections may cause malfunctions, unsufficient power supply or

interferences.

IMPORTANT NOTE: Due to the very high power consumption, the X4-MAXXIMUS model has two power terminals, which

must be both connected. Furthermore we suggest the installation of an additional battery. Please use a power wiring

with a crosssection of at least 2 x 35mm

in 4 ohm-operation.

IMPORTANT NOTE: The X4-MAXXIMUS model has due to construction-conditioned reasons no internal fuse-protection.

The amplifier must be fused with an external In-Line-Fuse aan the following fuse values:

200 A in 4 Ohm-operation

300 A in 2 Ohm-operation

400 A in 1 Ohm-operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics X4 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info