Bedienungsanleitung Hifonics ZRX4002 (Seite 21 von 32) (Deutsch, Englisch)

700133

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

FUNCTIONAL INSTRUCTIONS

Installation of RCA/Audio signal cables and power supply cables.

Ensure while installation not to lead the audio cables between the head unit and the amplier together with the power supply wires

on the same side of the vehicle. The best is a real separated installation on the left and right cable channel of the vehicle to avoid

interferences on the audio signal. This stands also for the enclosed bass-remote wire, which should not be installed together with the

power supply wires.

NOTE

SPEAKER CABLES

SHIELD

TO THE LINE IN ON THE

AMPLIFIER

CORE CONDUCTOR

The LEVEL controller adjusts the input sensitivity of the amplier, to adjust the audio signal of the headunit. The input sensitivity

is adjustable from 6 Volts (MIN) to 0.2 Volts (MAX).

The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.

The LINE OUT RCA jacks provide a linear fullrange audiosignal to supply an additional amplier.

HI LEVEL INPUTS & AUTO TURN ON

If your head unit has no pre-amplier low level RCA outputs or doesn’t provide a separate remote turn on wire (like described on

page 19/#2), follow these instructions:

AUTO TURN ON

Bring the AUTO TURN ON switch to position ON to activate the auto turn on function. This function only works, if the push button

INPUT LEVEL MODE is in HI position and highlevel inputs (speaker outputs from the headunit) are connected at the LINE IN.

Please check the regarding notes below.

The amplier detects now by the so called ”DC Offset” (a voltage increase to 6 volts on the high level speaker outputs) if the

head unit is turned on and the amplier turns automatically on. As soon as the head unit is turned off, the amplier shuts down

automatically after approx.one minute.

NOTE: The AUTO TURN ON usually works with 90% of all headunits, because they are equipped with the ”High Power” outputs.

Only with a few older headunits the AUTO TURN ON function is not applicable.

The port of the remote connector of the amplier (page 19#2, REM) can now be used also to turn on additional other ampliers.

Connect the REM ports of the ampliers and ensure, that the other amplier’s AUTO TURN ON function is deactivated.

High level speaker cables as signal input:

Please use the optional HF-HLA adaptor from HiFonics (see

page 28). This adaptor is optmized for the use with this amplier

inputs and owns additionally a protect function for the speaker

outputs of your headunit.

Alternative: Solder the ends of the loudspeaker cables of the

head unit with common RCA connectors (separately available)

and connect them with LINE IN of the amplier.

The HI LEVEL INPUTS can be use independently from the AUTO

TURN ON function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics ZRX4002 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info