700133

Hifonics ZRX4002 Seite 26

26
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
26
TROUBLE SHOOTING
ELECTRICAL INTERFERENCES
The reason for interferences are mostly the routed cables and wires. Especially the power and audio cables (RCA) of your sound system
are vulnerable. Often these interferences are caused by electric generators or other electrical units (fuel pump, AC etc.) of the car. The
most of these problems can be prevented by a correct and careful wiring.
Here are some courtesy notes:
1. Use only double or triple shielded audio RCA cables for the connection between the amplier and headunit. An useful alternative
are represented by anti-noise-devices or additional ancillary equipment like Balanced Line Transimtters, which you can purchase
at your car audio retailer. If possible do not use anti-noise-lters, which are splicing the ground of the RCA audio cables.
2. Do not lead the audio cables between the head unit and the amplier together with the power supply wires on the same side of
the vehicle. The best is a real separated installation on the left and right cable channel of the vehicle. Then the overlapping
of interferences on the audio signal will be avoided. This stands also for the enclosed bass-remote wire, which should not be installed
together with the power supply wires.
3. Avoid ground loops by connecting all ground connections in a starlike arrangement. The suitable ground center point is
ascertainable by measuring the voltage directly on the vehicle’s battery by a multi-meter. You should measure the voltage with
turned-on inginition (acc.) and with other turned-on power consumers (e.g. headlights, rear window defroster, etc,). Compare
the measured value with the voltage of the ground point you have choosen for the installation and the positive pole (+12V) of
the amplier. If the voltage has just a little difference, you have found a suitable ground point. Otherwise you need to choose an
other ground point.
4. Use if possible only cables with added or soldered cable sockets or the like. Gold plated or high value nickel plated cable sockets
are corrosionfree and own a very low contact resistance.
PROTECTION CIRCUIT
This amplier owns a 3-way protection circuit. On overloading, overheating, shorted loudspeakers, too low impedance or insufcient pow-
er supply, the protection circuit turns off the amplier to prevent serious damage. If one of this disfunctions is detected, the red PROTECT
LED lights up.
In this case, check all connections to detect short-circuits, faulty connections or overheating. Refer to the notes on the next page.
If the reason for the disfunction is eliminated, the amplier is ready for operation again.
If the red PROTECT LED does not stop to light up, the amplier is damaged. In this case return the amplier to your car audio retailer
with a detailled malfunction description and a copy of the proof of purchase.
WARNING: Never open the amplier and try to repair it by yourself. This causes a loss of warranty. The repairing service should be made
only by skilled technicians.
INSTALLATION AND OPERATION IN NEWER VEHICLES!
In many vehicles (since approx. 2002) computer controlled diagnosis- and controlling systems are applied - like CAN-BUS or MOST-BUS
interfaces. With the installation of a car audio amplier a new appliance will be added to the 12V on-board electrical system, which may
cause under several circumstances error messages or may interrupt the factory made diagnosis system, as a result of high stress peaks
and a higher power consumption. Thus, depending on model and manufacturer, the driving safety or important security systems like
airbags, ESC or others could be interrupted.
If you plan to operate the amplier in a vehicle like described above, please follow these instructions:
• Let the installation be made only by a skilled specialist or a service station, which is specialized for the maintenance of your vehicle.
• After the installation, we suggest to make a computer diagnosis of the on-board system, to detect possible malfunctions or errors.
• If the on-board system is interfered by the installation of the amplier, an additionally installed power capacitor can stabilize the electrical
on-board system to ensure a proper and stable operation.
• The best solution is the integration of an own additional 12 V electrical system for the sound system, which can be operated
independently with an own battery supply.
CONSULT YOUR CAR SPECIALIZED SERVICE STATION!
… 26 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics ZRX4002 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info