Bedienungsanleitung Hikoki AC18DA (Seite 13 von 236) (Alle Sprachen)

816327

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

English

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because

it has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the charge indicator lamp of the charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for

0.3 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○ When the charge indicator lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 3 2

Charging 4 2

Adjusting operating speed*152

Switch operation*263

How to use the LED light 7 3

How to use the hook*383

Removing the holder 9 3

Exchanging the rack (push-out rod)*410 4

Types of pistons*511 4

Exchanging the piston*612 4

Attaching the 300 ml holder 13-a 4

Attaching the 400 ml/600 ml holder 13-b 4

Using cartridges*714 5

Using sausages*715 5

Using buckets*716 5

Temporarily setting down the tool

while working*817 6

Removing hardened sealing

material*918 6

Remaining battery indicator 19 6

Charging a USB device from a

electrical outlet 20-a 6

Charging a USB device and battery

from a electrical outlet 20-b 6

How to recharge USB device 21 6

When charging of USB device is

completed 22 6

Selecting accessories ―228

*1 Adjusting operating speed

This can be performed even while working. Adjust the

speed together with the amount that the switch is pulled.

CAUTION

If the diameter of the cross section of the nozzle is 3 mm

or smaller, or if there is an attempt to abruptly dispense

at high speed while under low-temperature conditions,

the sealing material may leak out on the piston side.

Begin at low speed, and gradually increase speed to suit

the hardness of the sealing material.

*2 Switch operation

Immediately after the switch is released, the piston

retracts slightly to prevent sealing material remaining at

the end of the nozzle from dripping.

*3 How to use the Hook

The hook can be used to hang up the unit

temporarilyduring operations.

CAUTION

The hook should never be used to hang the unit on your

person.

When using the hook, check to make sure that the main unit

will not slip and fall, or become unstable by the wind, etc.

Never hang the unit from your belt or trousers as this could

cause accidents.

*4 Exchanging the rack (push-out rod)

NOTE

Install the rack (push-out rod) with its teeth facing

downward.

The rack (push-out rod) for 300 ml can also be used for

400 ml.

*5 Types of pistons

There are 3 types of pistons for diﬀ erent sealing

materials.

a: Cartridges

b: Sausages

c: Buckets

Choose a holder and piston according to the sealing

material.

*6 Exchanging the piston

The piston can be detached from the rack (push-out rod)

by twisting the piston counter-clockwise. To attach it,

twist it in the opposite direction to screw it in. Exchanging

it does not require any tools.

*7 Using cartridges, sausages, and buckets

CAUTION

Do not make the diameter of the cut cross-section of the

nozzle 3 mm or smaller. Doing so may cause leakage

of sealing material on the piston side or damage to the

holder or holder cap.

*8 Temporarily setting down the tool while working

NOTE

The tool can be temporarily set down upside-down while

working. When doing so, set it down on a stable surface.

*9 Removing hardened sealing material

Use the pin included with the 300 ml holder to scrape out

and remove the hardened portion of the sealing material

inside the nozzle and cartridge, then return the pin to the

holder.

NOTE

Be careful not to scratch the inside of the container with

the pin.

00BookAC18DAEU.indb1300BookAC18DAEU.indb13 2022/05/1910:34:072022/05/1910:34:07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki AC18DA Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info