Bedienungsanleitung Hikoki CB3612DA (Seite 17 von 332) (Alle Sprachen)

816321

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

English

If there is sagging or damage, request a replacement

from HiKOKI Authorized Service Center, as it may result

in the band saw blade running unstable or coming loose.

NOTE

Periodically remove any shavings, etc. that has adhered

to the blade pulley rubbers.

Failure to do so may result in slippage of the band saw

blade and/or injury.

3. Inspection of band saw blade back ball bearing

supports (Fig. 15)

Periodically inspect the band saw blade back ball

bearing supports inside the bearing holders for wear.

If the band saw blade back ball bearing supports are

worn, there will be excessive force on the band saw

blade that could result in damage to the band saw blade.

If the band saw blade back ball bearing supports are

worn, arrange for replacements from HiKOKI Authorized

Service Center.

4. Inspection of band saw blade guide rollers supports

and adjustment of gaps (Fig. 16)

After continued use of the unit, the gaps between the

band saw blade guide rollers supports may become

wider.

If the gaps become wider, the band saw blade may tilt,

resulting in reduced cutting precision.

Periodically inspect whether the gaps between the

band saw blade guide rollers supports are appropriate

(rollers are lightly touching the band saw blade), and

make any adjustments if necessary.

Additionally, if the band saw blade guide rollers supports

are damaged, arrange for replacements from HiKOKI

Authorized Service Center.

Remove blade pulley covers (A) and (B), and remove the

band saw blade.

(See Fig. 12 for band saw blade installation and

removal)

Use a ﬂ athead screwdriver to loosen the bearing pins.

Place the band saw blade between the guide rollers

supports and tighten the bearing pins, adjusting as

necessary to make sure that the blade is lightly in contact

with the supports.

Guide rollers

Bearing pin

Tighten

Loosen

Band saw blade

Fig. 16

Install the band saw blade, and install blade pulley

covers (A) and (B).

(See Fig. 12 for band saw blade installation and

removal)

5. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

6. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

7. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

8. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

9. Storage

After use, store in a dry location with a temperature

below 50°C that is out of the reach of children.

○ Do not store in a location that children can reach or easily

access.

○ Do not store in a location where the unit may be exposed

to rain such as under the eaves of a house, or where

there is humidity

○ Do not store in a location where there are sudden

changes in temperature or where there is direct sunlight.

○ Do not store in a location where there are volatile

substances that have a danger of igniting or exploding.

CAUTION

When removing the band saw blade and storing the

power tool, rotate the tension lever to the tightening side

and install the blade pulley cover.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

00BookCB3612DA.indb1700BookCB3612DA.indb17 2022/07/0116:49:002022/07/0116:49:00

Hikoki CB3612DA Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info