Bedienungsanleitung Hikoki CD3605DB (Seite 17 von 300) (Alle Sprachen)

816368

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

English

Table 3

Protective Function Overheat Protection Overload Protection

Tool Status Motor stopped during operation Motor stopped during operation

LED Lighting Status 0.5 second 0.1 second

Lighting Condition of

the Display Lamp Power mode: Light OFF

Silent mode: Light ON Power mode: Light OFF

Silent mode: Light ON

Cause Motor at high temperature Motor is overloaded

Countermeasure Allow the unit to fully cool down.

LED blinking should stop approximately

10 seconds after releasing the switch.

Remove the cause of the overload.

LED blinking should stop approximately

10 seconds after releasing the switch.

6. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

7. Storage

Store the power tool and battery in a place in which

the temperature is less than 40°C and out of reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

DISPOSING OF CHIPS (Fig. 25)

WARNING

When disposing chips, make sure that the tool is

switched oﬀ and that the battery is removed.

NOTE

○ Immediately after cutting steel materials, the chips and

the dust box may be hot. Do not touch them directly.

○ When disposing of the chips, do not allow the chips to

enter the motor portion of the tool body or the battery

mount.

○ Before changing the material to cut, dispose of the chips

that are in the dust box.

CAUTION

○ Dispose of the chips that are in the dust box before they

accumulate above the marks.

○ Failure to do so will reduce the eﬃ ciency of the dust

collecting. Additionally, the heat of the chips may deform

the dust box.

(1) Press the hook on the bottom of the dust cover, open the

dust cover, and dispose of the chips that are in the dust

box.

(2) Close the dust cover, and fasten the hook.

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade

Since use of as dull saw blade will degrade eﬃ ciency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Motor unit maintenance

The motor winding is an important part of this tool. Avoid

damaging and be careful to avoid contact with cleaning

oil or water.

Dust or particle accumulation in the motor can result in

damage.

4. Inspecting and maintaining the lower guard

Always make sure that the lower guard moves smoothly.

In the event of any malfunction, immediately repair the

lower guard.

5. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

00BookCD3605DBEU.indb1700BookCD3605DBEU.indb17 2022/06/2215:19:392022/06/2215:19:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CD3605DB Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info