Bedienungsanleitung Hikoki CG25EUAP (Seite 10 von 268) (Alle Sprachen)

816437

Zoom out

Zoom in

Vorherige Seite

1/268

Nächste Seite

English

WARNING

Improper maintenance could result in serious engine

damage or in serious personal injury.

Transport and storage

○ Carry the unit/machine by hand with the engine stopped

and the muﬄ er away from your body.

○ Allow the engine to cool, empty the fuel tank, and secure

the unit/machine before storing or transporting. Failure to

do so may result in ﬁ re or accidents.

○ Empty the fuel tank before storing the unit/machine. It is

recommended that the fuel be emptied after each use. If

fuel is left in the tank, store so fuel will not leak.

○ Store unit/machine out of the reach of children.

○ Clean and maintain the unit carefully and store it in a dry

place.

○ Make sure engine switch is oﬀ when transporting or

storing.

○ When transporting and storing, either remove the cutting

attachment or place the blade cover over the blade.

○ You have to secure the machine during transport to

prevent loss of fuel, damage or injury.

○ If a warning label cannot be read, peels oﬀ or becomes

indistinct, replace it with a new one. To purchase new

labels, contact HiKOKI Authorized Service Centers.

If situations occur which are not covered in this manual, take

care and use common sense. Contact HiKOKI Authorized

Service Centers if you need assistance.

SPECIFICATIONS

The SPECIFICATIONS of this machine are listed in the table

on page 261.

NOTE

All data subject to change without notice.

ASSEMBLY PROCEDURES

Installation of handle

(1) Loop handle type (Fig. 4)

Attach the handle to the drive shaft tube.

Adjust the location to the most comfortable position

before operation.

Make sure to securely attach the handle with the 4 bolts.

NOTE

If your unit has handle location label (8) on drive shaft

tube, follow the illustration.

(2) Bike handle type (Fig. 5)

Remove the handle bracket (9) from the assembly.

Place the handles and attach the handle bracket with

four bolts lightly. Adjust to appropriate position. Then

attach it ﬁ rmly with the bolts.

Attach the protection tube to the drive shaft tube or

handle using cord clamps (10) to make sure there is no

slack. (Fig. 6)

Installation of harness

WARNING

If the product includes a harness, always make sure to

use it.

Attach the harness hook (11) to the hanger (12) on the drive

shaft tube. (Fig. 7)

Adjust the length of the harness for easy operation of the

tool.

NOTE

You may need to adjust the position of the hangar (12)

to balance the unit. To do so, loosen bolt (13) and adjust

the position of hangar (12). After adjusting as necessary,

make sure to securely tighten the bolt (13). (Fig. 7)

Installation of cutting attachment guard

WARNING

If an incorrect or faulty guard is ﬁ tted, this may cause

serious personal injury.

CAUTION

Some cutting attachment guards are equipped with

sharp line limiters. Be careful with handling it.

NOTE

○ When using a trimmer head with two piece type cutting

attachment guard, attach the guard extension to the

cutting attachment guard, then tighten the bolt (14).

(Fig. 8)

○ The guard bracket may come already mounted to the

gear case on some models.

Align the cutting attachment guard with the guard bracket

(15) and secure it to the drive shaft tube, using the bolt and

guard holder (16) (if so equipped). (Fig. 9)

WARNING

Remove the guard extension when using metal or plastic

blades. Failure to do so may result in injury or damage to

the cutting attachment guard.

NOTE

To remove the guard extension, refer to the drawings.

Wear gloves as the extension has a sharp line limiter.

Loosen the bolt (14). Then push the three square tabs

on the guard one by one in order.(Fig. 10)

Installation of cutting attachment

WARNING

○ Install the cutting attachment properly and securely as

instructed in the handling instructions.

If not attached properly or securely, it may come oﬀ and

cause serious and/or fatal injury.

○ Do not install or remove cutting attachments while the

engine is running.

○ Always use genuine HiKOKI cutting attachments and

metal ﬁ ttings.

Installation of semi-auto cutting head

(if so equipped)

1. Function

Automatically feeds more nylon cutting line when it is

tapped at low rpm (not greater than 6000 min-1).

Speciﬁ cations

Code

No.

Type of

attaching

screw

Direction of

rotation

Size of

attaching

screw

6600570 Female screw Counter-

clockwise M10xP1.25-

Applicable nylon cord

Cord diameter: Φ2.4 mm Length: 5 m

2. Precautions

○ The case must be securely attached to the cover.

○ Check the cover (17), case (18) and other components

for cracks or other damage. (Fig. 11)

○ Check the case and button for wear.

If there is a hole in the bottom (19) of the button, change

the new parts immediately. (Fig. 11)

○ The cutting head must be securely mounted to the unit’s

gear case.

○ If the cutting head does not feed cutting line properly,

check that the nylon line and all components are properly

installed. Contact HiKOKI Authorized Service Centers if

you need assistance.

0000BookCG25EUAP.indb100000BookCG25EUAP.indb10 2019/01/2417:12:592019/01/2417:12:59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CG25EUAP Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info