Bedienungsanleitung Hikoki CG40EAF(LP) (Seite 13 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

816434

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

Fuel ﬁ lter (Fig. 30)

Remove the fuel ﬁ lter from the fuel tank, and replace it if it is

dirty.

NOTE

A blocked fuel ﬁ lter can prevent the supply of fuel and

cause a rotation malfunction of the engine.

Spark plug (Fig. 31)

The spark plug condition is inﬂ uenced by:

○ An incorrect carburetor setting.

○ Wrong fuel mixture (too much oil in the gasoline)

○ A dirty air ﬁ lter.

○ Hard running conditions (such as cold weather).

These factors cause deposits on the spark plug electrodes,

which may result in malfunction and starting diﬃ culties. If

the engine is low on power, diﬃ cult to start or runs poorly at

idling speed, always check the spark plug ﬁ rst.

If the spark plug is dirty, clean it and check the electrode

gap. Re-adjust if necessary. The correct gap is 0.6 mm. The

spark plug should be replaced after about 100 operation

hours or earlier if the electrodes are badly eroded.

NOTE

In some areas, local law requires using a resistor spark

plug to suppress ignition signals. If this machine was

originally equipped with resistor spark plug, use same

type of spark plug for replacement.

Gear case (Fig. 32)

Check gear case or angle gear for grease level about every

50 hours of operation by removing the grease ﬁ ller plug on

the side of gear case.

If no grease can be seen on the ﬂ anks of the gears, ﬁ ll the

gear case with quality lithium based multipurpose grease up

to 3/4. Do not completely ﬁ ll the gear case.

CAUTION

○ Make sure to remove any dirt or grit when attaching the

plug to its original position.

○ Before attempting inspection or maintenance of the gear

case, make sure the case has cooled.

Blade (Fig. 33)

WARNING

Wear protective gloves when handling or performing

maintenance on the blade.

○ Use a sharp blade. A dull blade is more likely to snag and

thrust.

Replace the fastening nut if it is damaged and hard to

tighten.

○ When replacing blade, purchase one recommended by

HiKOKI, with a 25.4 mm (one inch) ﬁ tting hole.

○ In the case of a 3 tooth blade (28), it can be used on

either side.

○ Use the correct blade for the type of work.

○ When replacing blades, use appropriate tools.

○ When cutting edges become dull, re-sharpen or ﬁ le

as shown in the illustration. Incorrect sharpening may

cause excessive vibration.

○ Discard blades that are bent, warped, cracked, broken

or damaged in any way.

NOTE

When sharpening blade it is important to maintain an

original shape of radius at the base of the tooth to avoid

cracking.

Nylon head

Nylon line replacement

○ Remove the cutting body cap by pushing inward the

locking tabs on the side of the nylon head (Fig. 34).

Take out the spool (Fig. 35), hook the new nylon line

into the hole of the spool, then wind it around the spool

(Fig. 36).

When the nylon line has been wound around the spool,

temporarily fasten it in the opening of the spool at about

10 cm from the end. (Fig. 37) Then thread the nylon line

through the hole on the side of the nylon head and place

the cutting body cap in reverse order of the cap removal

(Fig. 38). Pull the right and left nylon lines until they are

secured about 15 - 16 cm from the end. (Fig. 39)

NOTE

Make sure that the right and left nylon lines are of equal

length since vibrations will otherwise increase.

Flexible shaft

Lubricate ﬂ exible shaft from clutch housing side by removing

it every 20 hours of use.

For long-term storage

Drain all fuel from the fuel tank. Start and let engine run until

it stops. Repair any damage which has resulted from use.

Clean the unit with a clean rag, or the use of high pressure

air hose. Put a few drops of two-cycle engine oil into the

cylinder through the spark plug hole, and spin the engine

over several times to distribute oil.

Cover the unit and store it in a dry area.

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions.

For further information please contact HiKOKI Authorized

Service Centers.

Daily maintenance

○ Clean the exterior of the unit.

○ Check that the harness is undamaged.

○ Check the cutting attachment guard for damage or

cracks. Change the guard in case of impacts or cracks.

○ Check that the cutting attachment is properly centered,

sharp, and without cracks. An oﬀ -center cutting

attachment induces heavy vibrations that may damage

the unit.

○ Check that the cutting attachment nut is suﬃ ciently

tightened.

○ Make sure that the blade cover is undamaged and that it

can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

○ Check that the unit is undamaged and free of defects.

Weekly maintenance

○ Check the starter, especially the cord.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap.

Adjust it to 0.6 mm, or change the spark plug.

○ Check that the angle gear is ﬁ lled with grease up to 3/4.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline.

○ Clean the exterior of the carburetor and the space

around it.

○ Clean the fan and the space around it.

000BookCG40EAF(LP)WE.indb13000BookCG40EAF(LP)WE.indb13 2019/01/1811:28:432019/01/1811:28:43

Hikoki CG40EAF(LP) Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info