816239

Hikoki CH3672DA Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/248
Nächste Seite
11
English
MOUNTING AND OPERATION
Action Figure Page
Inserting the battery cover 2 2
Charging 3 2
Removing and inserting the
battery 42
Switch ON 5 2
Switch OFF 6 3
Blade case 7 3
Speed adjustment 8 3
Battery level 9 3
Sharpening the blade 10 3
Charging a USB device from a
electrical outlet 11-a 4
Charging a USB device and
battery from a electrical outlet 11-b 4
How to recharge USB device 12 4
When charging of USB device is
completed 13 4
Selecting accessories ―238
ABOUT USB DEVICE
○ Charging a USB device from an electrical outlet.
(Fig. 11-a)
○ Charging a USB device and battery from an electrical
outlet. (Fig. 11-b)
○ How to recharge USB device. (Fig. 12)
○ When charging of USB device is completed. (Fig. 13)
MAINTENANCE AND INSPECTION
WARNING
○ Be sure to turn the tool off and remove the battery
from the tool before making inspections or carrying out
maintenance.
○ Do not disassemble to blade. Failure to heed this
warning may result in injury.
○ Use gloves, or cloth to protect your hands when handling
the blade. Failure to heed this warning may result in
injury.
1. Sharpening the blade (Fig. 10)
Move an iron fi le in the direction of the arrow for a rough
sharpening then use an oil stone to give the blade a good
fi nish.
(1) Use a fi ne iron fi le or one of intermediate coarseness.
(2) Coat the oil stone with machine oil (bicycle oil or the like).
(3) Use a whetstone to gently remove any burrs from the
back of the blade edge.
When to sharpen the blade
While this will vary the type of trees that are trimmed and
how often it is used, it is a good idea to sharpen the blade
about once a year to maintain a sharp edge.
NOTE
Do not use water for cleaning the blade to prevent rust or
other damage.
2. Lubricating the blade
During trimming, sap adhering to the blade edge will
increase load and wear down the battery more rapidly.
Use machine oil (or bicycle oil or the like) to lubricate the
blade and wipe the blade with a cloth. To prevent the
blade from rusting, be sure to lubricate the blade after
use and when it will not be used for an extended period
of time before placing it in the blade case.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
0000BookCH3656DA.indb110000BookCH3656DA.indb11 2023/05/0911:26:322023/05/0911:26:32
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikoki CH3672DA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info