Bedienungsanleitung Hikoki CJ110MV (Seite 5 von 120) (Alle Sprachen)

816394

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

English

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must be

returned to HiKOKI Authorized Service Center for the

cord to be replaced.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI power tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the power tool, undismantled, with the GUARANTEE

CERTIFICATE

found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance with

the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the each terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 97 dB (A).

Measured A-weighted sound pressure level: 86 dB (A).

Uncertainty K: 5 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Cutting boards:

Vibration emission value ah, B = 6.7 m/s2 (CJ110MV)

Uncertainty K = 1.5 m/s2

Vibration emission value ah, B = 11.6 m/s2 (CJ110MVA)

Uncertainty K = 1.5 m/s2

Cutting sheet metal:

Vibration emission value ah, M = 3.4 m/s2 (CJ110MV)

Uncertainty K = 1.5 m/s2

Vibration emission value ah, M = 6.4 m/s2 (CJ110MVA)

Uncertainty K = 1.5 m/s2

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diﬀ er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

0000BookCJ110MV.indb50000BookCJ110MV.indb5 2022/02/0114:32:192022/02/0114:32:19

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CJ110MV Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info