Bedienungsanleitung Hikoki CR 18DA (Seite 11 von 112) (Alle Sprachen)

742719

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used,

the pilot lamp of the charger lights up green or lights

for 1 second, does not light for 0.5 seconds (oﬀ for 0.5

seconds). In such a case, ﬁ rst let the battery cool, then

start charging.

○ When the pilot lamp ﬂ ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with chargers

are taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery

Charging 3 2

Switch Operation 4 3

Mounting the blade

Mounting the Jigsaw blade

Dismounting the blade

7-a 4

Select a saw blade of the

appropriate length

Fasten a workpiece ﬁ rmly 9 5

Adjusting the base 10 5

Plunge cutting (for wood)

11 5

Selecting accessories ― 105

*1 Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

*2 Mounting the blade

(1) Turning the blade holder in the direction indicated by

the arrow, insert the blade all the way into the small

slit of the blade holder. (Fig. 5-b)

(2) The blade will be locked in place when the blade

holder is released.

The blade can be attached facing up or down

depending on the operation.

(3) Pull the back of the saw blade two or three times by

hand and check that the blade is securely mounted.

(Fig. 5-c)

NOTE

The blade can be mounted without ﬁ tting it into the base.

However, in this case, always make sure that the base is

attached to the tool after mounting the blade.

*3 Mounting the jigsaw blade (sold separately)

A T-shank jigsaw blade can be used with this product.

(Fig. 5-a)

Mounted in the same manner as a reciprocating saw

blade. Make sure that the shank of the blade is ﬁ tted into

the center cavity. (Fig. 6)

Pull the back of the saw blade two or three times by hand

and check that the blade is securely mounted. (Fig. 5-c)

*4 Dismounting the blade

CAUTION

Never touch the saw blade immediately after use. The

metal is hot and can easily burn your skin.

(1) After turning the blade holder, point the blade downward.

The blade should fall out on its own. If the blade fails to

fall out, pull it out by hand.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and remains inside

the small slit of the blade holder, it should fall out when

the blade holder is turned, and the blade is pointed

downward. If the blade fails to fall out on its own, take it

out by using the procedures described below.

(1) If a part of the broken saw blade is sticking out of the

small slit of the blade holder, pull out the protruding part

and take the blade out.

(2) If the broken saw blade is hidden inside the small slit,

hook the broken blade using a tip of another saw blade

and take it out. (Fig. 7-b)

*5 Plunge cutting (for wood)

NOTE

○ Using the collar or the base as support, gradually cut in

from the tip of the blade.

○ As the base is metal, using it for support may scratch

or damage the surface depending on the material

being cut. In this case, use the collar as support. If you

remove the base when window cutting, make sure it is

re-attached to the tool when you continue operating the

tool.

0000Book_CR18DA.indb 110000Book_CR18DA.indb 11 2020/05/14 12:08:182020/05/14 12:08:18

Hikoki CR 18DA Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info