Bedienungsanleitung Hikoki CR18DB (Seite 13 von 236) (Alle Sprachen)

816372

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

English

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 99 dB (A)

Measured A-weighted sound pressure level: 88 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Cutting boards:

Vibration emission value ah, B = 8.29 m/s2

Uncertainty K = 1.5 m/s2

Cutting wooden beams:

Vibration emission value ah, WB = 11.33 m/s2

Uncertainty K = 1.5 m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use

of the power tool can diﬀ er from the declared total

value depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

0000BookCR18DBEU.indb130000BookCR18DBEU.indb13 2022/12/0115:48:142022/12/0115:48:14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CR18DB Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info