Bedienungsanleitung Hikoki CS40EA (Seite 14 von 212) (Alle Sprachen)

816442

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

English

NOTE

When spring arrives and carburetor will not suﬀ er from

icing, make sure that the shutter is reinstalled in ordinary

position. (Fig. 42-a)

For long-term storage

Drain all fuel from the fuel tank. Start and let engine run until

it stops. Repair any damage which has resulted from use.

Clean the unit with a clean rag, or the use of high pressure

air hose. Put a few drops of two-cycle engine oil into the

cylinder through the spark plug hole, and spin the engine

over several times to distribute oil.

Cover the unit and store it in a dry area.

CHAIN SHARPENING

Parts of a cutter (Fig. 43, 44)

WARNING

○ Gloves should be used when sharpening chain.

○ Be sure to round oﬀ the front edge to reduce the chance

of kickback or tie-strap breakage.

49. Top plate

50. Cutting corner

51. Side plate

52. Gullet

53. Heel

54. Chassis

55. Rivet hole

56. Toe

57. Depth gauge

58. Correct angle on top plate (degree of angle depends on

chain type)

59. Slightly protruding “hook” or point (curve on non-chisel

chain)

60. Top of depth gauge at correct height below top plate

61. Front of depth gauge rounded oﬀ

LOWERING DEPTH GAUGES WITH A FILE

WARNING

○ Do not smoothen the upper part of the bumper drive links

(62) with a ﬁ le or deform them. (Fig. 45)

○ Adjust the depth gauge to the speciﬁ ed setting.

Failure to observe the above raises the possibility of a

kickback and may result in injury.

1) If you sharpen your cutters with a ﬁ le holder, check and

lower the depth.

2) Check depth gauges every third sharpening.

3) Place depth gauge tool on cutter. If depth gauge projects,

ﬁ le it level with the top of the tool. Always ﬁ le from the

inside of the chain toward an outside cutter. (Fig. 46)

4) Round oﬀ front corner to maintain original shape of

depth gauge after using depth gauge tool. Always follow

the recommended depth gauge setting found in the

maintenance or operator manual for your chain saw.

(Fig. 47)

GENERAL INSTRUCTIONS FOR FILING CUTTERS

File (63) cutter on one side of the chain from the inside out.

File on forward stroke only. (Fig. 48)

5) Keep all cutters the same length. (Fig. 45)

6) File enough to remove any damage to cutting edges

(side plate (64) and top plate (65)) of cutter. (Fig. 49)

SHARPENING ANGLES FOR SHARPENING SAW CHAIN

The SHARPENING ANGLES FOR SHARPENING SAW

CHAIN of this machine are listed in the table on page 208.

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions.

For further information please contact HiKOKI Authorized

Service Centers.

Inspection and service before use

○ Check that no damage is observed in the Anti-Vibration

springs, and no loosening or damage is observed in their

ﬁ xtures.

○ Check that no deformation or damage is observed in the

front and rear handles.

○ Check that the ﬁ xtures for front and rear handles are

suﬃ ciently tightened and free of damage.

○ Check that bolts, nuts, etc. used for each part are

suﬃ ciently tightened and free of damage.

Daily maintenance

○ Clean the exterior of the unit.

○ Clean the chain oil ﬁ lter port.

○ Clean the groove and oil ﬁ lter port in the guide bar.

○ Clean the side case of saw dust.

○ Check that the saw chain is sharp.

○ Check that the guide bar clamp nuts are suﬃ ciently

tightened.

○ Make sure that the guide bar cover is undamaged and

that it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

○ Check the tip of the guide bar. Please exchange it for the

new one when it is worn out.

○ Check the band of chain brake. Please exchange it for

the new one when it is worn out.

○ Make sure that the chain brake is operating.

After deactivating the machine by turning oﬀ the Stop

Switch, activate the chain brake and pull the saw chain

by hand. If the saw chain does not move, the chain brake

is operating properly.

Also, make sure to wear gloves when pulling the saw

chain.

○ Check that the chain does not rotate when the engine is

idling.

○ Clean the air ﬁ lter.

Weekly maintenance

○ Check the recoil starter, especially cord.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap.

Adjust it to 0.6 mm or change the spark plug.

○ Clean the cooling ﬁ ns on the cylinder and check that the

air intake at the recoil starter is not clogged.

Monthly maintenance

○ Rinse the fuel tank with gasoline, and clean fuel ﬁ lter.

○ Clean chain oil ﬁ lter.

○ Clean the exterior of the carburetor and the space

around it.

Quarterly maintenance

○ Clean the fan and the space around it.

○ Clean the carbon of muﬄ er.

CAUTION

Cleaning of fan and muﬄ er shall be done by HiKOKI

Authorized Service Centers.

GUIDE BAR AND SAW CHAIN COMBINATIONS

The guide bar and saw chain combinations of this machine

are listed in the table on page 208.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 208.

000BookCS40EA.indb14000BookCS40EA.indb14 2019/01/2512:32:242019/01/2512:32:24

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CS40EA Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info