Bedienungsanleitung Hikoki D10VF (Seite 3 von 124) (Alle Sprachen)

816287

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

English

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

DRILL SAFETY WARNINGS

Safety instructions for all operations

a) Use the auxiliary handle(s).

Loss of control can cause personal injury.

Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

Safety instructions when using long drill bits

a) Never operate at higher speed than the maximum

speed rating of the drill bit.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

b) Always start drilling at low speed and with the bit tip

in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

c) Apply pressure only in direct line with the bit and do

not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

1. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

(Fig. 15)

2. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

3. Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

4. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

5. Hold the drill and side handle securely with both hands

when using.

6. Do not wear gloves made of stuﬀ liable to roll up such as

cotton, wool, cloth or string, etc.

7. Prior to drilling into walls, ceilings or ﬂ oors, ensure there

are no electric cables or conduits inside.

8. Drilling

○ When drilling, start the drill slowly, and gradually

increasing speed as you drill.

○ Always apply pressure in a straight line with the bit. Use

enough pressure to keep drilling, but do not push hard

enough to stall the motor or deﬂ ect the bit.

○ To minimize stalling or breaking through the material,

reduce pressure on drill and ease the bit through the last

part of the hole.

○ If the drill stalls, release the trigger immediately, remove

the bit from the work and start again. Do not click the

trigger on and oﬀ in an attempt to start a stalled drill. This

can damage the drill.

○ The larger the drill bit diameter, the larger the reactive

force on your arm.

Be careful not to lose control of the drill because of this

reactive force.

To maintain ﬁ rm control, establish a good foothold,

use side handle, hold the drill tightly with both hands,

and ensure that the drill is vertical to the material being

drilled.

○ Precautions on boring

The drill bit may become overheated during operation;

however, it is suﬃ ciently operable. Do not cool the drill

bit in water or oil.

○ Caution concerning immediately after use

Immediately after use, while it is still revolving, if the Drill

is placed on a location where considerable ground chips

and dust have accumulated, dust may occasionally be

absorbed into the drill mechanism. Always pay attention

to this undesirable possibility.

9. Attaching the angle unit. (Optional accessory for D13VF

and D13VG)

(1) Removing chuck from drill (Fig. 10)

○ If the chuck cannot be removed by striking the wrench,

don’t strike the wrench forcibly and send the drill to a

HiKOKI AUTHORIZED SERVICE CENTER.

(2) Removing chuck from angle unit (Fig. 12)

○ The chuck can be removed from angle unit in the same

manner it was removed from the drill; however, ALWAYS

REMOVE ANGLE UNIT FROM THE DRILL BEFORE

ATTEMPTING TO LOOSEN CHUCK. This will prevent

damage of drills gear. Use open end wrench provided to

hold angle unit spindle before attempting to loosen chuck.

○ If the chuck cannot be removed by striking the wrench,

don’t strike the wrench forcibly and send the drill to a

HiKOKI AUTHORIZED SERVICE CENTER.

10. When the power tool is used with a hook ﬁ xed to it, pay

attention to the following points:

○ Before hanging the main unit from the waist belt, make

sure that the drill has come to a complete stop.

While it is suspended from the waist belt, the power plug

must be disconnected from the power source.

○ Do not walk about with the power tool hanging from the

waist belt.

○ In the case of operation in a high place, it is dangerous

to drop the tool accidentally. If the hook is deformed or

hung from the wrong position, there is danger that the

hook will slip oﬀ and the tool will fall.

Be careful to avoid danger.

○ In making a through hole, the power tool sometimes

shakes violently when the workpiece is pierced, from

example. Be careful you are not hurt by the hook even if

such situation happens.

00BookD10VF.indb300BookD10VF.indb3 2022/12/2711:24:132022/12/2711:24:13

Hikoki D10VF Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info