Bedienungsanleitung Hikoki D10VST(L) (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

816433

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

HOW TO USE

1. Switch operation

○ When the trigger is depressed, the tool rotates. When the

trigger is released, the tool stops.

○ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

○ Pulling the trigger and pushing the stopper, it keeps

the switched-on condition which is convenient for

continuous running. When switching oﬀ , the stopper can

be disconnected by pulling the trigger again. (Fig. 5)

2. Drilling

○ When drilling, start the drill slowly, and gradually

increasing speed as you drill.

○ Always apply pressure in a straight line with the bit. Use

enough pressure to keep drilling, but do not push hard

enough to stall the motor or deﬂ ect the bit.

○ To minimize stalling or breaking through the material,

reduce pressure on drill and ease the bit through the last

part of the hole.

○ If the drill stalls, release the trigger immediately, remove

the bit from the work and start again. Do not click the

trigger on and oﬀ in an attempt to start a stalled drill. This

can damage the drill.

○ The larger the drill bit diameter, the larger the reactive

force on your arm.

Be careful not to lose control of the drill because of this

reactive force.

To maintain ﬁ rm control, establish a good foothold, hold

the drill tightly with both hands, and ensure that the drill is

vertical to the material being drilled.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded eﬃ ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI AUTHORIZED

SERVICE CENTER.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it has

to be done by HiKOKI Authorized Service Center to avoid

a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

STANDARD ACCESSORIES

○ Chuck wrench (Spec. only for keyed chuck) ................1

Standard accessories are subject to change without notice..

APPLICATIONS

○ Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If the

plug is connected to a receptacle while the power switch

is in the ON position, the power tool will start operating

immediately, inviting serious accident.

3. Extension cord

When the work area is removed from the power source.

Use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. Selecting the appropriate drill bit:

○ When boring metal or plastic

Use ordinary metalworking drill bits.

○ When boring wood

Use ordinary woodworking drill bits.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

5. Mounting and dismounting of the bit

For keyed chuck (Fig. 1)

(1) Open the chuck jaws, and insert the bit into the chuck.

(2) Place the chuck wrench in each of the three holes in the

chuck, and turn it in the clockwise direction (viewed from

the front side). Tighten securely.

(3) To remove the bit, place the chuck wrench into one of

the holes in the chuck and turn it in the counterclockwise

direction.

For keyless chuck (Fig. 2)

(1) Open the chuck jaws, and insert the bit into the chuck.

To open the chuck jaws, hold the ring while turning the

sleeve in the counterclockwise direction (viewed from the

front side).

(2) Firmly grasp the ring and turn the sleeve in the clockwise

direction. Tighten securely.

(3) To remove the bit, ﬁ rmly grasp the ring and turn the

sleeve in the counterclockwise direction.

(4) If it is hard to loosen the sleeve, ﬁ x the spindle using the

open-end wrench, hold the sleeve ﬁ rmly, and turn it in the

loosening direction (counterclockwise when viewed from

the front). (Fig. 3)

6. Check the rotational direction (Fig. 4)

The bit rotates clockwise (viewed from the rear side) by

turning the rotational change lever to R-mark.

The rotational change lever is returned to the L-mark to

turn the bit counterclockwise.

(The

and marks are provided on the body.)

7. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

00BookD10VST(L)WE.indb800BookD10VST(L)WE.indb8 2021/03/0911:07:472021/03/0911:07:47

Hikoki D10VST(L) Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info