Bedienungsanleitung Hikoki D36DYA (Seite 12 von 220) (Alle Sprachen)

816206

Zoom out

Zoom in

Vorherige Seite

1/220

Nächste Seite

English

HOW TO USE

1. Fixing the body in place

○ If a load is applied to the bit when drilling holes, the tool

may be pushed out of control in the opposite direction

by recoil.

To reduce the load applied to the bit, use a well-

sharpened bit that is appropriate for the type of work.

Place the bit straight against the surface to be drilled.

○ Try to avoid drilling holes in wood that is bent, damp, or

has many knots. Also, ensure that there are no nails or

other metal objects inside the wood.

○ When drilling existing holes to make them larger, or

when the bit goes all the way through the material, be

careful as a load may be applied to the bit.

○ Placing the side handle against a pillar, etc. while

working can prevent the tool body from jerking out of

control. (Fig. 14-a, Fig. 14-b)

2. Slip clutch

During work, the slip clutch activates when a large load

is suddenly applied, which causes the transmission

between the motor and the bit to slip, and the bit

rotation stops. If this feature activates and the drill

rotation stops, quickly stop the switch.

NOTE

The slip clutch only activates when the change lever is

in low speed (“1”).

MAINTENANCE AND INSPECTION

WARNING

Be sure to turn off the switch and remove the battery

before maintenance and inspection.

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

5. Cleaning on the outside

When the power tool is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

6. Storage

Store the power tool and battery in a place in which the

temperature is less than 40°C and out of reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

significantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, significantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to five times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when the

battery is disassembled and modified (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO4871.

Measured A-weighted sound power level: 93dB (A)

Measured A-weighted sound pressure level: 85dB (A)

Uncertainty K: 5 dB (A)

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Drilling into metal:

Vibration emission value

, D < 2.5m/s2

Uncertainty K = 1.5m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use of

the power tool can differ from the declared total value

depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that are

based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time).

2023/03/17 15:26:17Stylesheet: EU Version: 2023.2.1

D36DYA_C99746771_303_EU

Hikoki D36DYA Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info