Bedienungsanleitung Hikoki DH28PEC (Seite 6 von 144) (Alle Sprachen)

816310

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

English

Table 1

Display

lamp

ﬂ ashing Cause Solution

Operation has

ceased because the

internal temperature

has exceeded the

temperature limit.

(High temperature

protection function)

Allow the unit to cool

for 15 to 30 minutes.

When the temperature

goes down, press the

changeover switch to

recover operation.

Excessive

pressure

applied to the

tool has resulted

in an overload

that shut oﬀ the

motor.

(Overload

protection

function)

Tool fails to

operate or shuts

down due to

the unit being

connected to

a high or low

voltage power

source.

Tool has shut

down due to a

voltage signal

read error that

occurred from

the unit’s power

cord being

plugged in and

out at short

intervals.

(Circuit

protection

function)

Press the

changeover switch

to recover. Switch

to low mode and

avoid excess

pressure when

operating the tool.

Connect the unit

to a power supply

matching the input

voltage speciﬁ ed

on the nameplate.

Press the

changeover switch

to recover.

Allow for an interval

of 3 seconds

or more when

plugging the power

cord in and out.

Press the

changeover switch

to recover.

Alternately

switch on

and oﬀ

Unit fails to activate

or ceases to

operate due to a

sensor signal read

error.

(Control monitoring

function)

Press the changeover

switch to recover.

Repair may be

required if this error

continuously occurs.

Sudden

overburdening of

the tool bit has

activated the RFC,

stopping further

operation of the tool.

RFC (See page 5

“REACTIVE

FORCE

CONTROL”)

Press the changeover

switch to recover.

Before continuing

operation, remove

the cause of the

overburden.

NOTE

Despite taking steps to correct a problem, the display

lamp may continue to blink. Should this be the case, the

unit may require repair. If so, please contact the outlet

from which this product was purchased for repairs.

LUBRICATION

This Rotary Hammer is of full air-tight construction to protect

against dust.

Therefore, this Rotary Hammer can be used without

lubrication for long periods. Replace the grease as described

below.

Grease Replacement Period

After purchase, periodically replace grease. Ask for grease

replacement at the nearest authorized Service Center.

CAUTION

A special grease is used with this machine, therefore,

the normal performance of the machine may be badly

aﬀ ected by use of other grease. Please be sure to let

one of our service agents undertake replacement of the

grease.

MAINTENANCE AND INSPECTION

1. Inspecting the tools

Since use of a dull tool will cause motor malfunctioning

and degraded eﬃ ciency, replace the tool with new ones

or resharpen them without delay when abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HIKOKI Authorized Service Center to

avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

0000BookDH28PEC.indb60000BookDH28PEC.indb6 2022/12/0714:01:122022/12/0714:01:12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki DH28PEC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info