Bedienungsanleitung Hikoki DH30PC2 (Seite 4 von 108) (Alle Sprachen)

816401

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

English

Concrete

Steel

Wood

Hammering only function

Rotation only function

Rotation and hammering function

Switching ON

Switching OFF

Disconnect mains plug from electrical outlet

Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

○ Plastic case ..................................................................1

○ Side handle ..................................................................1

○ Stopper ........................................................................1

○ Dust cup .......................................................................1

○ Syringe .........................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

Rotation and hammering function

○ Drilling anchor holes

○ Drilling holes in concrete

○ Drilling holes in tile

Rotation only function

○ Drilling in steel or wood

(with optional accessories)

○ Tightening machine screws, wood screws

(with optional accessories)

Hammering only function

○ Light-duty chiselling of concrete, groove digging and

edging.

SPECIFICATIONS

The speciﬁ cations of this machine are listed in the Table on

page 95.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Inserting SDS-plus drilling tools 1 96

Removing SDS-plus drilling tools 2 96

Selecting the operating mode 3 96

Adjusting the drilling depth 4 96

Changing the chisel position 5 96

Switching on and oﬀ and setting

the speed 696

Replacing carbon brushes 7 97

Installing the side handle 9 97

Selecting accessories* – 98, 99

* For detailed information regarding each tool, contact a

HiKOKI authorized service center.

LUBRICATION

Low viscosity grease is applied to this rotary hammer so that

it can be used for a long period without replacing the grease.

Replace the grease whenever you change the carbon brush

to maintain the service life.

Further use of the rotary hammer with lock oﬀ grease will

cause the machine to seize up reduce the service life.

CAUTION

A special grease is used with this machine, therefore,

the normal performance of the machine may be badly

aﬀ ected by use of other grease. Please be sure to let

one of our service agents undertake replacement of the

grease.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning

and degraded eﬃ ciency, replace the drill bit with new

ones or resharpen them without delay when abrasion is

noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 7)

The Motor employs carbon brushes which are

consumable parts. When they become worn to or near

the “wear limit” ⓐ, it results in motor trouble.

When an auto-stop carbon brush is equipped, the motor

will stop automatically. At that time, replace both carbon

brushes with new ones which have the same carbon

brush Numbers ⓑ shown in the Fig. 7. In addition,

always keep carbon brushes clean and ensure that they

slide freely within the brush holders.

5. Replacing carbon brushes (Fig. 7)

Remove the brush caps ⓔ and carbon brushes. After

replacing the carbon brushes, do not forget to tighten the

brush caps securely and to install the tail cover.

00BookDH30PC2EU.indb400BookDH30PC2EU.indb4 2022/10/2110:33:382022/10/2110:33:38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki DH30PC2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info