Bedienungsanleitung Hikoki DH3628DC (Seite 15 von 300) (Alle Sprachen)

816262

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

English

SELECT OPERATION MODE

Pressing the changeover switch allows the selection of

rotation speed and the auto stop function.

○ Rotation speed (Low mode/Normal mode) (Fig. 17)

Select either Low mode or Normal mode and operate the

tool in the selected speed.

○ Auto stop mode (on/oﬀ ) (Fig. 18)

This product is equipped with an auto stop function to

support continuous drilling work. The function features a

memory mode for storing the work time for drilling from

switch ON to switch OFF, and an auto stop mode that

automatically stops the motor from the second drilling

onward should the work exceed the stored work time

while the switch is ON.

AUTO STOP FUNCTION

In selection mode, pressing the button for longer than two

seconds will move to memory mode. (Fig. 18)

(At the same time the auto stop lamp will blink.)

Conduct drilling when the auto stop lamp is ﬂ ashing. The

time between switching ON and switching OFF is stored by

the tool.

(At the same time, the auto stop lamp will light up.)

Conduct drilling when the auto stop lamp is ﬂ ashing.

Continuous drilling is possible as the memory storage time

will be recorded by the tool until the auto stop function’s auto

stop mode is cancelled.

The auto stop function is cancelled by pressing the

changeover switch once again for over two seconds.

(At the same time, the auto stop lamp will switch oﬀ .)

CAUTION

○ Switch ON the tool once you place the tip of the tool on

the work material.

○ The rotation speed and the level at which the switch is

pulled during drilling is not stored to memory.

○ Fully carry out drilling in one go during auto stop mode.

○ The motor will stop even if you switch OFF within the

memory storage time.

○ When you switch OFF within the memory storage time,

the count will be reset. If you rework a task in which a

hole has been partially drilled, the memory storage time

will be fully recounted.

○ The auto stop function will remain active until canceled.

REACTIVE FORCE CONTROL

This product is equipped with a Reactive Force Control

(RFC) feature that reduces jerking of the tool body.

If the tool bit is suddenly overburdened, any jerking of the

tool body is reduced by activation of the slip clutch or by

stopping of the motor by the sensor built into the tool body.

If the motor is stopped because of overburdening detection

by the controller, the display lamp will blink while the switch

is pulled. In addition, the lamp will continue blinking for

approximately three seconds after the switch is released.

The motor will remain stopped while the lamp is blinking.

(Fig. 26)

Because the RFC feature may not activate or its performance

may be insuﬃ cient depending on the working environment

and conditions, be careful not to suddenly overburden the

tool bit while operating.

● Possible causes of sudden overburdening

Tool bit biting into material

Impact against nails, metal or other hard objects

Tasks involving prying or any excess application of

pressure, etc.

Also, other causes include any combination of the

aforementioned.

● When the reactive force control (RFC) is triggered

When the RFC is triggered and the motor stops, turn

oﬀ the tool’s switch and remove the cause of the

overburdening before continuing operation.

Fig. 26

LED LEVEL FUNCTION

The LED level function uses a red or green LED to indicate

whether the tool is horizontal or vertical.

1. To turn on the LED level function during use, pull the

switch trigger gently. Press the level LED switch when

the display lamp on the panel lights up. (Fig. 1)

2. The level LED on the tool side lights up or blinks in the

color shown below when the level LED switch is pressed.

(Fig. 19)

Green lights: Within 5° of horizontal or vertical

Green blinks: Within 5°–10° of horizontal or vertical

Red lights: Not within 10° of horizontal or vertical

CAUTION

○ This function does not work while drilling holes (while the

trigger switch is pulled). Use it to check tilting of the tool

before or after drilling.

○ The angle is approximate.

3. Press the level LED switch once again to turn it oﬀ .

The previous settings will be retained once it is turned

back on again.

CAUTION

○ This function indicates vertical and horizontal directions

with respect to gravity and does not indicate whether the

tool is perpendicular to surfaces that may be at an angle.

○ The LED level function detects tilt for surfaces (such

as walls) that are perpendicular with respect to gravity

(Fig. 19-a (43) (44)), but it cannot detect horizontal

tilting with respect to the surfaces (Fig. 19-b (45) (46)).

0000BookDH3628DA.indb150000BookDH3628DA.indb15 2022/12/0915:14:272022/12/0915:14:27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki DH3628DC Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info