Bedienungsanleitung Hikoki DH40MEY2 (Seite 8 von 136) (Alle Sprachen)

816313

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

English

PPower Input

n0No-load speed

Bpm Full-load impact rate

max Drilling diameter, max.

Weight

(According to EPTA-Procedure 01/2014)

Drill bit

Core bit

Adjustment of the tool position function

Hammering only function

Rotation and hammering function

Switching ON

Switching OFF

Rotation speed selector switch

Display lamp

Ls Low speed / impact rate

Hs High speed / impact rate

Disconnect mains plug from electrical outlet

Class II tool

SDS max shank

Warning

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

○ Plastic case .................................................................1

○ Side handle .................................................................1

○ Hammer Grease A ......................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

Rotation and hammering function

○ Drilling anchor holes

○ Drilling holes in concrete

Hammering only function

○ Crushing concrete, chipping, digging, and squaring

(Some applications need optional accessories)

SPECIFICATIONS

The speciﬁ cations of this machine are listed in the Table on

page 126.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Inserting SDS-MAX tools 22

Removing SDS-MAX tools 32

Changing tool direction 4 2

Selecting the operating mode 5 3

Installing the side handle 6 3

Switching on and oﬀ 73

Speed change*110 4

Installing the stopper 11 4

Mounting core bit 12 5

Mounting guide plate and center pin 13 5

Selecting accessories*2–127, 128

*1 When drilling fragile materials, or when conducting

chipping operations or alignment operations, change

the tool’s rotation speed in accordance with the task by

using the rotation speed selector switch.

NOTE

While the tool’s motor is operating, rotation speed

cannot be adjusted by pressing the rotation speed

selector switch.

To adjust rotation speed, switch oﬀ the tool. Once the

motor has stopped, press the rotation speed selector

switch to adjust the speed.

*2 For detailed information regarding each tool, contact a

HiKOKI authorized service center.

Operate this Rotary Hammer by utilizing its own weight. The

performance will not be better even if it is pressed or thrust

forcibly against the work surface.

Hold this Rotary Hammer with a force just suﬃ cient to

counteract the reaction.

Warming up (Fig. 14)

The grease lubrication system in this unit may require

warming up in cold regions.

Position the end of the bit so makes contact with the

concrete, turn on the switch and perform the warming

up operation. Make sure that a hitting sound is produced

and then use the unit.

CAUTION

When the warming up operation is performed, hold the

side handle and the main body securely with both hands

to maintain a secure grip and be careful not to twist your

body by the jammed drill bit.

00BookDH40MEY2.indb800BookDH40MEY2.indb8 2023/06/1316:35:252023/06/1316:35:25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki DH40MEY2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info