Bedienungsanleitung Hikoki FCJ65V3 (Seite 8 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

816403

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

4. Storing the hexagonal bar wrench

(1) Insert in a hole on the side of the main unit with

holding the short side horizontally as shown in

Fig. 2.

(2) Rotate with the hexagonal bar wrench inserted and

secure as shown in Fig. 2.

ADJUSTING THE GUIDE ROLLER

The guide roller, shown in Fig. 3, is employed to prevent

the blade from snapping. Prior to use, adjust guide roller in

accordance with the following procedures:

(1) Loosen the holder set screw with the accessory

hexagonal bar wrench.

(2) Gently slide the guide roller until the roller groove lightly

touches the back of the blade.

NOTE

On delivery from the factory, there is a gap of about

3 mm between the roller and blade.

(3) Firmly tighten the holder set screw.

CAUTION

○ The guide roller can be used only for Blades that

have a straight line on the rear that is longer than

50 mm. (Fig. 4A and 4B) When using other types of

blades (Fig. 4C), slide the guide roller in backwards

so that the guide roller does not contact the blade.

○ When cutting thick boards or performing continuous

cutting operations, use the blade shown in the

Fig. 4A, 4B and be sure to set the guide roller.

CHIP COVER POSITIONING

1. Chip cover

Use the chip cover to reduce ﬂ ying of cut particles and

to easily operate the saw.

Slide the chip cover while lightly pressing its front

section.

The chip cover can be set at three positions as shown in

Fig. 5.

2. How to choose the position of the chip cover

Set the chip cover to the ﬁ rst step when attaching or

removing the blade.

Set the chip cover to the second step when cutting

wooden materials.

Set the chip cover to the second or third step when

cutting metal materials such as steel.

CAUTION

○ Keep always the chip cover in the low position when

operating the tool.

○ Wear protection glasses even if the chip cover is used.

ADJUSTING THE BLADE OPERATING SPEED

The blade operating speed can be adjusted within a range

of 0 to 3,000 min–1 according to the degree that the trigger

switch is depressed. Select the speed appropriate to the

material being worked and/or the working conditions.

To achieve continuous operation, pull the trigger switch

all the way back and depress the stopper. Then, turn the

speed adjustment knob to adjust the blade operating

speed as desired.

NOTE

The speed adjustment knob rotates approximately 1.5

turns. To turn the switch OFF, pull the trigger switch again

to disengage the stopper, and release the trigger switch.

CUTTING

CAUTION

○ While sawing, the base must be ﬁ rmly in contact with

the material surface, and the blade must be held at a

right angle. If the base becomes separated from the

material, it could cause the blade to break.

○ When cutting while holding the front surface, be careful

of the moving blade and hold the upper part ﬁ rmly.

1. Rectilinear cutting

(1) To ensure accurate rectilinear cutting, employ the

optional accessory guide as shown in Fig. 6.

(2) Use the splinter guard to reduce roughness of the

cutting surface of wooden materials. Attach the splinter

guard by inserting it from the front section of the base

until it clicks into place. (Fig. 7)

CAUTION

Set the base in the front position when using the splinter

guard.

2. Cutting a circle or a circular arc

To ensure eﬃ cient cutting, employ the optional

accessory guide and nail or wood screw as shown in

Fig. 8.

When mounting the guide, loosen the base bottom

screw, and shift the base as far forward as it will go.

3. Sawing curved lines

When sawing a small circular arc, reduce the feeding

speed of the machine. If the machine is fed too fast, it

could cause the blade to break.

4. Cutting metallic materials

Always use an appropriate cutting agent (spindle

oil, soapy water, etc.). When a liquid cutting agent is

not available, apply grease to the back surface of the

material to be cut.

5. Pocket cutting

(1) In lumber

Aligning the blade direction with the grain of the wood,

cut step by step until a window hole is cut in the center

of the lumber. (Fig. 9)

(2) In other materials

When cutting a window hole in materials other than

lumber, initially bore a hole with a drill or similar tool

from which to start cutting.

6. Angular cutting

Set the chip cover to the ﬁ rst step. (Fig. 5)

To adjust the angle of inclination; loosen the base

bottom screw, shift the base position to the side groove

of the semicircular portion, align the scale on the base

semicircular portion (ﬁ gures engraved on the scale

indicate the angle of inclination) with the housing edge

line, and thoroughly tighten the base bottom screw.

(Fig. 10 and 11)

CAUTION

Set the screw to the opposite side of the inclining side

when using the guide. (Fig. 12)

7. Dust produced in operation

CAUTION

○ To prevent accidents, turn the switch oﬀ and remove the

plug from the power supply when not in use.

○ For instruction on using the dust collector and

applicable cutting debris, please read the dust collector

instruction manual.

The dust produced in normal operation may aﬀ ect

the operator’s health. Either of following way is

recommended.

a) Wear a dust mask

b) Use external dust collection equipment

000BookFCJ65V3WE.indb8000BookFCJ65V3WE.indb8 2022/02/0215:16:512022/02/0215:16:51

Hikoki FCJ65V3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info