Bedienungsanleitung Hikoki G 3613DB (Seite 8 von 280) (Alle Sprachen)

742697

Zoom out

Zoom in

Vorherige Seite

1/280

Nächste Seite

English

toward or away from the operator, depending on direction of

the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a ﬁ rm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up.

The operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade.

Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC FOR

GRINDING AND ABRASIVE CUTTING-

OFF OPERATIONS

a) Use only wheel types that are recommended for

your power tool and the speciﬁ c guard designed

for the selected wheel.

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

b) The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequately protected.

c) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-oﬀ wheel.

Abrasive cut-oﬀ wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

e) Always use undamaged wheel ﬂ anges that are of

correct size and shape for your selected wheel.

Proper wheel ﬂ anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-oﬀ

wheels may be diﬀ erent from grinding wheel ﬂ anges.

f) Do not use worn down wheels from larger power

tools.

Wheel intended for larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

ADDITIONAL SAFETY WARNINGS

SPECIFIC FOR ABRASIVE CUTTING-

OFF OPERATIONS

a) Do not “jam” the cut-oﬀ wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind

the rotating wheel.

When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel

the spinning wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut

for any reason, switch oﬀ the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the cut-

oﬀ wheel from the cut while the wheel is in motion

otherwise kickback may occur.

Investigate and take corrective action to eliminate the

cause of wheel binding.

d) Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut.

The wheel may bind, walk up or kickback if the power

tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Use extra caution when making a “pocket cut” into

existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

GENERAL SAFETY INSTRUCTIONS

FOR CORDLESS DISC GRINDERS

– Check that speed marked on the wheel is equal to or

greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible with

the grinder;

– Abrasive wheels shall be stored and handled with care in

accordance with manufacturer’s instructions;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are ﬁ tted in

accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are provided

with the bonded abrasive product and when they are

required;

– Ensure that the abrasive product is correctly mounted

and tightened before use and run the tool at no-load for

30 seconds in a safe position, stop immediately if there

is considerable vibration or if other defects are detected.

If this condition occurs, check the machine to determine

the cause;

– If a guard is equipped with the tool never use the tool

without such a guard;

– When using a abrasive cutting wheel, be sure to remove

the standard accessory wheel guard and attach the

wheel guard with side guard (sold separately) (

Fig. 5);

– Do not use separate reducing bushings or adapters to

adapt large hole abrasive wheels;

– For tools intended to be ﬁ tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to

accept the spindle length;

000Book_G3613DA_DB_EU.indb 8000Book_G3613DA_DB_EU.indb 8 2019/12/26 11:53:532019/12/26 11:53:53

Hikoki G 3613DB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info