Bedienungsanleitung Hikoki G13BYEQ2 (Seite 10 von 184) (Alle Sprachen)

816284

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

English

○ Rotation recovery control function

When the motor is stopped due to overloading, if the

cause is eliminated, the motor automatically resumes

operation.

During grinding, if the motor stops due to pressing too

forcefully with the grinder, gently lift the tool body to start

rotation again.

When the motor is stopped for a certain period of time,

it does not recover, for the protection of the unit and for

safety.

Turn it oﬀ once and on again to start it.

○ Overheat protection

This protection feature cuts oﬀ the power to the motor

and stops the power tool in the event of overheating of

motor during operation.

When the overheat protection feature has been

activated, the motor may stop.

In this case, release the tool switch and cool it down in a

few minutes.

After that you can use it again.

○ Brake function

Brake activates when the trigger is oﬀ .

○ Brake sytstem workable even in a power outage

The brake system works reliably even if there is a power

outage or unplugging during operation in order to avoid

unexpected accident.

NOTE

○ To prevent the tip tool from falling oﬀ , the brake will not

be applied when the switch is released right after startup.

○ Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Attaching and removing the guard

clip*132

Fitting and adjusting the wheel guard*242

Fixing the side handle 5 3

Assembling depressed center wheel*3 *4

Assembling cutting wheel and diamond

wheel*3 *473

Switch operation*583

Grinding angle and grinding method*693

Cutting work*710 4

Selecting accessories*8— 175

*1 Attaching and removing the guard clip

Pull on the tabs while removing the guard clip.

When attaching the guard clip, ensure that its tabs

(2 locations) are hooked on the rim of the wheel guard.

*2 Fitting and adjusting the wheel guard

The wheel guard can be adjusted to an optimal angle for

the work.

Fix the wheel guard in place where its hole is aligned with

the bump of the lever before use.

*3 Sold separately

*4 WARNING

Before use, be sure to tighten the wheel nut with the

included wrench.

Failure to tighten could result in the wheel nut

loosening when the brake is activated during a stop.

NOTE

The wheel washer (C) is speciﬁ cally for this product.

Do not use it for any other product.

*5 When the 0 voltage re-start protection feature has been

activated, return the power switch to the OFF position

and wait for 1 second or more before restarting the

power tool.

*6 Grinding angle and grinding method

Press down the machine evenly on the surface and

move back and forth so that the surface of the workpiece

does not become too hot.

Rough grinding: position the machine at an angle of

15°–30° for the best working results.

When the grinding stone is new, its corner may dig in

when it is pushed forward, so pull back as shown in “a”

during use.

Once the wheel edge is worn, the workpiece can be

ground in both directions.

*7 Cutting work

Always work against the run of the disc. Otherwise there

is the danger of the machine kicking back from the cut

out of control. Guide the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

*8 WARNING

Do not use the following accessories. Doing so may

prevent correct operation of the switch.

○ Dust collection guard for diamond cutting disc (Code

No. 377085)

○ Dust collection guard for diamond cutting disc (with

guide roller) (Code No. 377086)

MAINTENANCE AND INSPECTION

WARNING

○ Be sure to switch power OFF and disconnect the plug

from the receptacle during maintenance and inspection.

○ Using cracked, deformed or damaged wheels can lead

to wheel breakage and resulting serious injury.

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

4. Filter cleaning and inspection

WARNING

Wear protective glasses and a dust mask when cleaning

the ﬁ lter with an air gun.

Failure to do so may result in inhalation or exposure of

the eyes to debris or dust.

After use, remove any debris or dust adhered to the ﬁ lter

using a soft brush. (Fig. 11) Check the ﬁ lter periodically

to ensure that it is free of scratching, chipping, or tearing.

Replace with a new ﬁ lter if the ﬁ lter is damaged in any way.

NOTE

If the mesh is clogged and the debris or dust cannot be

removed, detach the ﬁ lter and clean it with an air gun,

etc. (See “Exchanging the ﬁ lter set (Fig. 12)”)

5. Exchanging the ﬁ lter set (Fig. 12)

NOTE

○ When detaching the ﬁ lter, be careful not to let debris

enter the tool body.

○ Leave the ﬁ lter set attached to the body, except when

cleaning or exchanging the ﬁ lter set.

00BookG13BYEQ2.indb1000BookG13BYEQ2.indb10 2022/12/2715:35:052022/12/2715:35:05

Hikoki G13BYEQ2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info