816339

Hikoki G1812DA Seite 14

14
Zoom out
Zoom in
Vorherige Seite
1/260
Nächste Seite
14
English
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 3 2
Charging 4 2
Fitting and adjusting the wheel guard 5 2
Fixing the side handle 6 3
Assembling depressed center
wheel*1, *273
Assembling cutting wheel and
diamond wheel*1, *283
Switch operation 9 4
Grinding angle and grinding method*3 10 4
Cutting work*4 11 4
Remaining battery indicator 12 4
Detaching and attaching the fi lter 13 4
Charging a USB device from a
electrical outlet 14-a 5
Charging a USB device and battery
from a electrical outlet 14-b 5
How to recharge USB device 15 5
When charging of USB device is
completed 16 5
Selecting accessories ―249
*1 sold separately
*2 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
NOTE
The wheel washer is specifi cally for this product. Do
not use it for any other product.
*3 Grinding angle and grinding method
Press down the machine evenly on the surface and
move back and forth so that the surface of the workpiece
does not become too hot.
Rough grinding: position the machine at an angle of
15°–30° for the best working results.
When the grinding stone is new, its corner may dig in
when it is pushed forward, so pull back during use.
(Fig. 10-a)
Once the wheel edge is worn, the workpiece can be
ground in both directions. (Fig. 10-b).
*4 Cutting work
Always work against the run of the disc. Otherwise there
is the danger of the machine kicking back from the cut
out of control. Guide the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
MAINTENANCE AND INSPECTION
WARNING
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Filter cleaning and inspection (Fig. 12)
WARNING
Wear protective glasses and a dust mask when cleaning
the fi lter with an air gun.
Failure to do so may result in inhalation or exposure of
the eyes to debris or dust.
After use, remove any debris or dust adhered to the fi lter
using a soft brush. Check the fi lter periodically to ensure that
it is free of scratching, chipping, or tearing. Replace with a
new fi lter if the fi lter is damaged in any way.
NOTE
○ If the mesh is clogged and the debris or dust cannot be
removed, detach the fi lter and clean it with an air gun,
etc.
○ After cleaning, make sure to securely attach the fi lter.
4. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
NOTE
In order to expel debris and dust, periodically run the
motor with no load.
5. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
6. Cleaning on the outside
When the cordless disc grinder is stained, wipe with a
soft dry cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
7. Storage
Store the power tool and battery in a place in which
the temperature is less than 40°C and out of reach of
children.
000BookG1812DAEU.indb14000BookG1812DAEU.indb14 2022/08/3015:34:312022/08/3015:34:31
… 14 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikoki G1812DA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info