816224

Hikoki G1813DF Seite 16

16
Zoom out
Zoom in
Vorherige Seite
1/284
Nächste Seite
16
English
While in Auto mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
lowered if the load decreases during operation.
NOTE
○ To enable mode changes, pull the switch once after
installing the battery.
○ The set mode remains set even if the power is turned off .
○ Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
<G1813DVE, G1813DVF>
Pressing the Auto mode switch will change the
operating mode back and forth between Auto mode and
Transmission mode.
With Transmission mode, the grinder’s number of
revolutions can be set at one of six levels using the dial.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
Set the mode and dial according to work application.
(Table 3)Table 3
Status Number of
Revolutions (min-1)Use
1 3200 Grinding stainless
steel
2 3800
Rust or paint removal
Grinding, fi nishing
3 4700
4 5400
Rough grinding,
cutting
5 6700
6 8000
Auto L 5500 Light work, Standby state
Auto H 8000 Grinding, cutting
Auto L: No-load
Auto H: During operation
<G1812DE, G1813DE, G1813DF>
Pressing the Auto mode switch will change the operating
mode back and forth between Auto mode and Full-Speed
mode. In Full-Speed mode, the number of revolutions is
controlled so that it always remains constant.
Set the mode according to work application.
*6 Grinding angle and grinding method
Press down the machine evenly on the surface and
move back and forth so that the surface of the workpiece
does not become too hot.
Rough grinding: position the machine at an angle of
15°–30° for the best working results.
When the grinding stone is new, its corner may dig in
when it is pushed forward, so pull back during use.
(Fig. 13-a)
Once the wheel edge is worn, the workpiece can be
ground in both directions. (Fig. 13-b).
*7 Cutting work
Always work against the run of the disc. Otherwise there
is the danger of the machine kicking back from the cut
out of control. Guide the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
*8 Remaining battery indicator (Product)
When using a battery with a remaining battery indicator,
please refer to the indicator lamp on the battery for the
battery remaining power.
MAINTENANCE AND INSPECTION
WARNING
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Filter cleaning and inspection (Fig. 17)
WARNING
Wear protective glasses and a dust mask when cleaning
the fi lter with an air gun.
Failure to do so may result in inhalation or exposure of
the eyes to debris or dust.
After use, remove any debris or dust adhered to the fi lter
using a soft brush. Check the fi lter periodically to ensure that
it is free of scratching, chipping, or tearing. Replace with a
new fi lter if the fi lter is damaged in any way.
NOTE
○ If the mesh is clogged and the debris or dust cannot be
removed, detach the fi lter and clean it with an air gun,
etc.
○ After cleaning, make sure to securely attach the fi lter.
4. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
NOTE
In order to expel debris and dust, periodically run the
motor with no load.
5. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
6. Cleaning on the outside
When the cordless disc grinder is stained, wipe with a
soft dry cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
7. Storage
Store the power tool and battery in a place in which
the temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
00BookG1812DEEU.indb1600BookG1812DEEU.indb16 2022/11/2814:50:502022/11/2814:50:50
… 16 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikoki G1813DF wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info