Bedienungsanleitung Hikoki G23SWA (Seite 10 von 156) (Alle Sprachen)

816386

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

English

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fitting and adjusting the wheel guard

Fixing the side handle 2 2

Assembling depressed center wheel

*1 33

Assembling cutting wheel*1 43

Switch operation*2 5-a 4

Switch operation (without Lock-on)*2 5-b 4

Grinding angle and grinding method

Replacing carbon brushes

Maintenance of the toolless wheel

guard 85

Selecting accessories ―146

*1 Securing/Releasing the "Quick" clamping nut (sold

separately)

〈Securing the "Quick" clamping nut〉

WARNING

Do not use the "Quick" clamping nut if the accessory

has a clamping shank thicker than 6 mm!

WARNING

Only use the "Quick" clamping nut when undamaged

and in perfect operating condition: the arrow must

point to the notch on the outer ring.

(1) Lock the spindle.

(2) Fit the "Quick" clamping nut on the spindle.

(3) Tighten the "Quick" clamping nut by turning clockwise

by hand.

(4) Turn the grinding wheel ﬁ rmly clockwise to tighten the

"Quick" clamping nut.

〈Releasing the clamping nut〉

(1) Lock the spindle.

(2) Turn the "Quick" clamping nut anticlockwise to

unscrew.

*2 When the 0 voltage re-start protection feature has been

activated, return the power switch to the OFF position and

wait for 1 second or more before restarting the power tool.

(For G23SWUA / G23SCA only)

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Inspecting the carbon brushes (Fig. 7)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brushes with new ones having the same carbon brush

No. ⓑ shown in the ﬁ gure when it becomes worn to or

near the “wear limit” ⓐ. In addition, always keep carbon

brushes clean and ensue that they slide freely within the

brush holders.

4. Replacing carbon brushes (Fig. 7)

〈Disassembly〉

(1) Loosen the D4 tapping screw ⓒ retaining the brush

cover ⓓ and remove the brush cover.

(2) Use the auxiliary hexagonal wrench or small screwdriver

to pull up the edge of the spring ⓔ that is holding down

the carbon brush. Remove the edge of the spring toward

the outside of the brush holder ⓕ.

(3) Remove the end of the pig-tail ⓖ on the carbon brush

ⓗ from the terminal section of brush holder and then

remove the carbon brush from the brush holder.

〈Assembly〉

(1) Insert the end of the pig-tail of the carbon brush in the

terminal section of brush holder.

(2) Insert the carbon brush in the brush holder.

(3)

Use the auxiliary hexagonal wrench or small screwdriver to

return the edge of the spring to the head of the carbon brush.

(4) Mount the brush cover and tighten the D4 tapping screw.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

6. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

0000BookG23STA.indb100000BookG23STA.indb10 2022/06/1511:56:102022/06/1511:56:10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki G23SWA Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info