816342

Hikoki G3613DE Seite 16

16
Zoom out
Zoom in
Vorherige Seite
1/288
Nächste Seite
16
English
*4 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
NOTE
The wheel washer is specifi cally for this product. Do
not use it for any other product.
*5 About the mode change function
With Auto mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
lowered if the load decreases during operation.
NOTE
○ To enable mode changes, pull the switch once after
installing the battery.
○ The set mode remains set even if the power is turned off .
○ Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
<
G3612DVE, G3613DVE, G3613DVF, G3615DVE, G3615DVF>
Pressing the Auto mode switch will change the
operating mode back and forth between Auto mode and
Transmission mode.
With Transmission mode, the grinder’s number of
revolutions can be set at one of six levels using the dial.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
Set the mode and dial according to work application.
(Table 3)
Table 3
Status
Number of
Revolutions (min-1)
Use
G3612DVE
G3613DVE
G3613DVF
G3615DVE
G3615DVF
1 3200 3200 Grinding stainless
steel
239
00
3600
Rust or paint removal
Grinding, fi nishing
3 5300 4600
4 7400 5600
Rough grinding,
cutting
5 8600 7200
6 10000 8000
Auto L 5500 5500 Light work, Standby
state
Auto H 10000 8000 Grinding, cutting
Auto L: No-load
Auto H: During operation
<G3613DE, G3613DF>
Pressing the Auto mode switch will change the operating
mode back and forth between Auto mode and Full-Speed
mode. In Full-Speed mode, the number of revolutions is
controlled so that it always remains constant.
Set the mode according to work application.
*6 Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
Wipe off any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
*7 Grinding angle and grinding method
Press down the machine evenly on the surface and
move back and forth so that the surface of the workpiece
does not become too hot.
Rough grinding: position the machine at an angle of
15°–30° for the best working results.
When the grinding stone is new, its corner may dig in
when it is pushed forward, so pull back during use.
(Fig. 14-a)
Once the wheel edge is worn, the workpiece can be
ground in both directions. (Fig. 14-b).
*8 Cutting work
Always work against the run of the disc. Otherwise there
is the danger of the machine kicking back from the cut
out of control. Guide the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 4. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
Table 4
Safeguard
Function LED Light Display Corrective
Action
Overburden
Protection On 0.1 second/
off 0.1 second Remove the
cause of the
overburdening.
Kickback
Protection
Temperature
Protection
On 0.5 second/
off 0.5 second
Allow the tool
and battery
to thoroughly
cool.
MAINTENANCE AND INSPECTION
WARNING
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
00BookG3612DVEEU.indb1600BookG3612DVEEU.indb16 2022/08/3016:25:462022/08/3016:25:46
… 16 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikoki G3613DE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info