Bedienungsanleitung Hikoki GM13Y (Seite 4 von 168) (Alle Sprachen)

816429

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

English

4 Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the rate

for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and must

be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories.

Check for misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the power tool’s

operation. If damaged, have the power tool

repaired before use. Many accidents are caused

by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected

situations.

5Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

General safety instructions for grinding:

Use

a) This power tool is designed for surface

grinding. Refer to all

safety warnings,

instruc-

tions, illustrations and specifications provided

with this power tool. Failure to follow all the

instructions may result in electric shock, fire and/or

serious injury.

b) This power tool is not suitable for routing,

polishing, sanding, working with roughing

discs, wire brushes, parting grinder discs or

flap discs. Using the power tool for tasks for which

it was not designed may create a hazard and cause

personal injury.

c) Do not use accessories that are not specifi-

cally designed and recommended by the tool

manufacturer. Just because an accessory can be

attached to your power tool does not mean safe

operation is guaranteed.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized acces-

sories cannot be adequately protected or

controlled.

f) Threaded mounting of accessories must

match the grinder spindle thread. For accesso-

ries mounted by flanges, the arbour hole of the

accessory must fit the locating diameter of the

flange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before

use, always check accessories for splinters or

cracks and check grinding wheels for cracks or

signs of severe wear and tear. If a power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory, posi-

tion yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute. Damaged accessories will normally break

apart during this test time.

h) Wear personal protective equipment.

Depending on the application, use a face

shield, safety goggles or safety glasses. As

appropriate, wear a dust mask, hearing protec-

tors, gloves and workshop apron capable of

stopping small abrasive or workpiece frag-

ments. The eye protection must be capable of stop-

ping flying debris generated by various operations.

The dust mask or respirator must be capable of

filtering particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away from

your work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of a workpiece or broken accessory may

fly into the air and cause injury beyond the imme-

diate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. A cutting acces-

sory that comes in contact with a "live" wire may

render exposed metal parts of the power tool "live"

and give the operator an electric shock.

Special Safety Instructions

GM13Y_C99742271_102.book 4 ページ２０２１年２月１８日　木曜日　午後１２時４６分

Hikoki GM13Y Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info