Bedienungsanleitung Hikoki GM13Y (Seite 7 von 168) (Alle Sprachen)

816429

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

English

Before plugging in the machine, check that the

rated mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Australia: Always use a residual current device

(RCD) protected supply with a rated residual

current of 30 mA or less.

1 Fitting of bar auxiliary handle

Always work with the bar auxiliary handle (1)

attached! Fit the bar auxiliary handle as shown

(Fig. 1).

- Fit locking discs (3) to the left and right of the gear

housing.

- Fit the bar auxiliary handle (1) at the gear housing.

- Insert the thumb screws (2) left and right into the

bar auxiliary handle (1) and turn gently.

- Adjust the bar auxiliary handle (1) to the required

angle.

- Firmly tighten the thumb screws (2) to the left and

right manually.

2 Dust extraction

Always use a suitable dust extraction system:

Connect an L-class and over vacuum cleaner

to the extractor connection piece (12).

For optimal dust extraction, use the connecting

sleeve.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle must be at a standstill.

1 Locking the spindle (Fig. 2)

Press in the spindle locking knob (11) only

when the spindle is stationary!

- Press in the spindle locking button (11) and turn

the spindle (9) by hand until you feel the spindle

locking button engage.

2 Fitting/removing the diamond cup wheel

(Fig. 2)

To fit:

- Fit the support flange (8) on the spindle. (9) The

flange should not turn on the spindle when prop-

erly attached.

- Lay the diamond cup wheel (7) on the support

flange (8) so that it lies flat along the support

flange.

- The two sides of the clamping nut (6) are different.

Screw the clamping nut onto the spindle so that

the band of the clamping nut (6) is facing upward.

- Lock the spindle. Turn the clamping nut (6) clock-

wise using the 2-hole spanner (5) to secure.

To remove:

- Lock the spindle. Turn the clamping nut (6) anti-

clockwise using the 2-hole spanner (5) to

unscrew.

1 Working close to walls (Fig. 3)

To open and close the segment: switch off the

machine and pull the mains plug. The acces-

sory must be stationary.

Only raise the segment (13) when working

close to walls. Otherwise, the segment must

be lowered.

The open area of the safety guard must face the

direction of the wall.

2 Setting the speed (Fig. 3)

Set the optimum speed on the setting wheel (18),

depending on the application.

A wheel setting of between 4 and 6 is suitable for

most applications.

3 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only set it

down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate on the work.

Torque activation

Switching on: Slide the trigger switch (16)

forwards and then push the trigger switch

(16) upwards.

Switching off: Release the trigger switch (16).

Initial Operation

Attaching the Accessory

Use

GM13Y_C99742271_102.book 7 ページ２０２１年２月１８日　木曜日　午後１２時４６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki GM13Y Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info