Bedienungsanleitung Hikoki GP18DB (Seite 12 von 240) (Alle Sprachen)

816414

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

English

○ When the pilot lamp ﬂ ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with chargers

are taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 2 2

Charging 3 2

Removal of a collet chuck 4 2

Installing a wheel*153

The attachment position of a wheel 6 3

Using the side handle*273

Switch operation 8 3

Dial of variable speed operation*394

Selecting accessories ―232, 233

*1 Installing a wheel (Fig. 5)

Install the wheel so that length ℓ is less than 15 mm. If ℓ

is longer, abnormal vibration will occur, and the machine

is not only negatively aﬀ ected, but there is a possibility of

a serious accident.

Make the ℓ as small as possible.

When d = 6 mm, 1/4", 8 mm, D of the wheel should be

less than the Max. wheel diameter (50 mm). If a wheel

with D more than the Max. wheel diameter (50 mm) is

used, the circumference speed exceeds the safety limit

and the wheel will break. Never use such a wheel.

Distance L varies for D. Determine L referring to the

Table 3.

When d = 3 mm, 1/8", D should be less than 10 mm.

Determine L referring to the Table 3.

Wheels can be simply attached and detached by using

the two wrenches. (Fig. 6)

NOTE

○ Do not tighten the collet chuck by inserting a shaft thinner

than the regular shaft diameter (6 mm) in the chuck or in

an empty condition. This practice will damage the collet

chuck.

○ When using a shaft (3 mm), switch to a collet chuck for

3 mm shaft (sold separately). (Fig. 4)

○ When installing a wheel with shaft, tighten the collet

chuck after applying a small quantity of spindle oil (or

sewing machine oil) to the tapered portion. (Fig. 5)

Table 3 (when ℓ = 15 mm)

dDL

3 mm,

3.175 mm (1/8")

5 mm 10 mm

6 mm 13 mm

8 mm 16 mm

10 mm 13 mm

6 mm,

6.35 mm (1/4")

13 mm 40 mm

16 mm 40 mm

20 mm 25 mm

25 mm 25 mm

32 mm 13 mm

38 mm 7 mm

8 mm

25 mm 32 mm

32 mm 25 mm

38 mm 19 mm

*2 Using the side handle

Install the side handle after removing the front cover.

Detach the front cover by removing the protrusion on

the interior from the hollow in the main unit and pull to

remove. If the protrusion is diﬃ cult to detach, use a ﬂ at-

head screwdriver or similar tool.

*3 Dial of variable speed operation

The unit has “Transmission mode” and “Auto mode”.

○ With Transmission mode, the grinder’s number of

revolutions can be set at one of ﬁ ve stages.

When operating in Transmission mode, the set number

of revolutions will be maintained regardless of changes

in load.

○ With Auto mode, you can lower noise and vibration by

lowering the maximum number of revolutions while in a

no-load state.

While in Auto mode, the number of revolutions will be

raised if the load becomes greater during operation.

On the other hand, the number of revolutions will be

lowered if the load decreases during operation. (Table 4)

○ Set the mode and dial according to work application.

Table 4

Mode Status Number of Revolutions (min-1) Use

Transmission

Dial Settings

1 7000 Polishing/ﬁ nishing

2 13800 Paint removal

3 16600 Rust removal

4 24400 Burr removal

5 29000 Grinding

Auto A 15000 Work on standby

29000 Grinding

00BookGP18DA.indb1200BookGP18DA.indb12 2021/03/1715:12:132021/03/1715:12:13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki GP18DB Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info