Bedienungsanleitung Hikoki GR800 (Seite 3 von 28) (Alle Sprachen)

816410

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH en

2.4 Extending guide rail

See page 2, ﬁ g. D.

Using the connector (order no. 4100080) two guide rails

can be joined.

Align the guide rails ﬂ ush. Push connector into the guide rail.

Tighten the four tappets in clockwise direction using the tool

provided.

2.5 Setting mitre guide

See page 2, ﬁ g. A.

Undo the knurled screw at the bottom side of the mitre

guide. Insert mitre guide into T-groove (1). Set desired

angle and tighten knurled screws again by hand.

Order no. 4100081

1. SPECIFIED CONDITIONS OF USE

The guide rails permit precise, splinter-free sawing of planks

and boards with the following HiKOKI hand-held circular

saws and HiKOKI plunge-type saws:

C3606DPA

Various circular saws of the following manufacturers

are compatible with this guide rail: Bosch, Festool, Hilti,

Metabo, Makita.

2. CIRCULAR SAWS WITH GUIDE

GROOVE

2.1 Clamping guide rail

See page 2, ﬁ g. A.

Using the tensioning clamps (711237) and the quick action

clamp (711238), the guide rail can be secured on the

workpiece for safe working and protection from slipping.

The tensioning clamps are pushed onto both sides of the

guide rail into the T-slot (1).

2.2 Attaching the machine

Descriptions for machines with a groove (2) in the circular

saw guide plate:

See page 2, ﬁ g. B.

- Mount the circular saw as shown on the guide rail. (The

groove (2) in the circular saw guide plate slides in the

proﬁ le (3) of the guide rail)

- Depending on the machine, gliding without play can be

set on the guide rail (see operating instructions of the

machine).

Diagonal cuts can be carried out in all angle settings.

2.3 Splinter Protection, Adhesive Coating and Sliding

Coating

Prior to attaching the Sliding Coating, the adhesive

remains on the guide rail must be removed completely

(if required using solvent)!

See page 2, ﬁ g. C.

Splinter Protection:

In new condition, the outside edge of the Splinter Protection

(6) protrudes slightly beyond the cutting track of the circular

saw blade. This protruding section is cut oﬀ in the ﬁ rst

cut. To avoid tearing, the Splinter Protection (6) should lie

completely on a support when sawing. The edge of the

Splinter Protection is then cutting edge of the workpiece.

When changing the circular saw, it is usually necessary to

replace the Splinter Protection with a new one. For easier

insertion of the new Splinter Protection (6) the front area can

be pulled out from the guide rail (about 2–3 cm) to permit

a safe grip (see page 2, ﬁ g. E). If the insertion by hand is

too diﬃ cult, pliers can be used to pull the Splinter Protection.

Since the insertion can cause lengthening of the Splinter

Protection, we recommend letting the guide track rest for a

while before cutting oﬀ the protruding ends of the Splinter

Protection. Spare Splinter Protections can be ordered under

order no. 4100077.

Adhesive Coating:

Replace the Adhesive Coating (4) in case of damage or

strong wear. Replacements can be ordered under order no.

4100079.

Sliding Coating:

Replace the Sliding Coating (5) in case of damage or

strong wear. Replacements can be ordered under order no.

4100078.

(Original instructions)

0000BookGR800.indb30000BookGR800.indb3 2022/08/0521:51:542022/08/0521:51:54

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki GR800 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info