Bedienungsanleitung Hikoki H25PV (Seite 8 von 100) (Alle Sprachen)

816379

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed in the below.

○ Case .............................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

Demolishing concrete, chipping oﬀ concrete, grooving, bar

cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility installation,

machinery installation, water supply and drainage work,

interior jobs, harbor facilities and other civil engineering

works.

SPECIFICATIONS

Voltage (by areas) (110 V, 230 V, 240 V)

Power Input 500 W

Full-load Impact Rate 0–3200 min-1

Weight

(According to EPTA-

Procedure 01/2014) 3.6 kg

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Mounting a tool 22

Dismounting a tool 32

Deciding working position of tool 42

Switch operation 53

How to use the demolition hammer*163

Replacing carbon brushes 73

Selecting accessories*2―5

*1 By utilizing the empty weight of the machine and

by ﬁ rmly holding the hammer with both hands, one

can eﬀ ectively control the subsequent recoil motion.

Proceed at a moderate work-rate, the use of too much

force will impair eﬃ ciency.

*2 For detailed information regarding each tool, contact a

HiKOKI authorized service center.

GREASE REPLACEMENT

This machine is of full air-tight construction to protect against

dust and to prevent lubricant leakage. This machine can be

used without grease supplement for an extended period of

time. However, perform the grease replacement to maintain

the service life. Replace the grease as described below.

1. Grease Replacement Period

You should look at the grease when you change the

carbon brush. (See item 4 in the section MAINTENANCE

AND INSPECTION.) Ask for grease replacement at the

nearest authorized HiKOKI Service Center.

In the case that you are forced to change the grease by

yourself, please follow the following points.

2. How to replace grease

CAUTION

Before replacing the grease, turn the power oﬀ and pull

out the plug from the receptacle.

(1) Remove the crank case cover and wipe oﬀ the old

grease inside. (Fig. 8)

(2) Supply 25 g (the standard volume to cover the connecting

rod) of HiKOKI Electric Hammer Grease A to the crank

case.

(3) After replacing the grease, install the crank case cover

securely. At this time, do not damage or lose the oil seal.

NOTE

The HiKOKI Electric Hammer Grease A is of the low

viscosity type. When the grease is consumed, purchase

from an authorized HiKOKI Service Center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident.

1. Inspecting accessories

Since use of a dull accessory, such as a bull point, a

cutter, etc. will degrade eﬃ ciency and cause possible

motor malfunction, sharpen or replace with a new one as

soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 7)

The Motor employs carbon brushes which are

consumable parts. When they become worn to or near

the “wear limit” ⓐ, it results in motor trouble.

When an auto-stop carbon brush is equipped, the motor

will stop automatically. At that time, replace both carbon

brushes with new ones which have the same carbon

brush Numbers ⓑ shown in the Fig. 7. In addition,

always keep carbon brushes clean and ensure that they

slide freely within the brush holders.

5. Replacing carbon brushes (Fig. 7)

Remove the brush caps ⓔ and carbon brushes ⓕ. After

replacing the carbon brushes, do not forget to tighten the

brush caps securely and to install the tail cover.

6. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

000BookH25PV.indb8000BookH25PV.indb8 2022/10/0614:51:492022/10/0614:51:49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki H25PV Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info