816221

Hikoki H3641DA Seite 13

13
Zoom out
Zoom in
Vorherige Seite
1/228
Nächste Seite
English
13
Action Figure Page
How to recharge USB device 18 6
When charging of USB device is
completed 19 6
Selecting accessories*3―215,
216
*1 When conducting chipping operations or alignment
operations, change the tool’s impact rate in accordance
with the task by using the impact rate selector switch.
NOTE
○ Impact rate cannot be adjusted until a battery is
installed to the power tool and the switch has been
triggered once.
○ While the tool’s motor is operating, impact rate cannot
be adjusted by pressing the impact rate selector switch.
To adjust impact rate, switch off the tool.
Once the motor has stopped, press the impact rate
selector switch to adjust the impact rate.
*2 Operate this Demolition Hammer by utilizing its empty
weight. The performance will not be better even if it is
pressed or thrust forcibly against the work surface.
Hold this Demolition Hammer with a force just sufficient
to counteract the reaction.
*3 For detailed information regarding each tool, contact a
HiKOKI authorized service center.
Warming up (Fig.14)
The grease lubrication system in this unit may require
warming up in cold regions.
Position the end of the bit so makes contact with the
concrete, turn on the switch and perform the warming up
operation. Make sure that a hitting sound is produced and
then use the unit.
ABOUT THE PROTECTION
FUNCTIONS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered during
operation, the display lamp will blink as described in
Table3. When any of the safeguard functions are
triggered, immediately remove your finger from the switch
and follow the instructions described under corrective
action.
Table 3
Display lamp
flashing Cause Solution
Flash
Internal
temperature has
risen beyond the
unit’s specified
temperature.
(Temperature
increase
protection
function)
Turn off the unit
and allow it to
cool down for
about 15 to
30minutes.
When the
temperature
goes down,
press the impact
rate selector
switch to
recover.
Display lamp
flashing Cause Solution
Flash
Excessive
pressure applied
to the tool has
resulted in an
overload.
(Overload
protection
function)
Press the impact
rate selector
switch to
recover. Try to
avoid tasks that
will apply excess
pressure to the
unit.
Flash Sensor signal
read error.
(Control
monitoring
function)
Press the impact
rate selector
switch to
recover. Repair
may be required
if this error
continuously
occurs.
GREASE REPLACEMENT
This Demolition Hammer is of full air-tight construction to
protect against dust.
Therefore, this Demolition Hammer can be used without
lubrication for long periods. Replace the grease as
described below.
Grease Replacement Period
After purchase, replace grease after every 6 months of
usage. Ask for grease replacement at the nearest
authorized Service Center.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turn off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the tool
Since use of as dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
2023/07/20 17:28:42Stylesheet: EU Version: 2023.6.21
H3641DA_C99749471_308_EU
… 13 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikoki H3641DA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info